You might try the N1MM LOGGER software here: http://pages.cthome.net/n1mm/
It will go up/down with the up/down arrow keys (100hz in SSB, 20hz in CW),
RIT/XIT and filters can be toggled with the mouse. Works great with my
ahhhh.... errr..... Kenwood (sorry). Have not used it with any FT rig but
many are supported.
Other points: it's free, it's Windoze based, supports Packet or Telnet DX
cluster access
TRY IT!
73, Bill N2BC
~~~~~~~~~~~~~~~~
Bill Coleman N2BC
http://home.stny.rr.com/n2bc
----- Original Message -----
From: "MikeR" <nf4l@pobox.com>
To: "Jim White, K4OJ" <k4oj@tampabay.rr.com>; <wulf@ping.net.au>
Cc: <yaesu@contesting.com>
Sent: Friday, November 29, 2002 11:05 AM
Subject: Re: [Yaesu] CAT FT990/FT1000 Problem: Clarifier Tuning
> Jim -
> If there is a separate knob, you're STILL gonna have to take a hand off
the
> keyboard arent't you ? Or did I miss something ? Now a foot operated
> slider.....
> 73, Mike NF4L
> ----- Original Message -----
> From: "Jim White, K4OJ" <k4oj@tampabay.rr.com>
> To: <wulf@ping.net.au>
> Cc: <yaesu@contesting.com>
> Sent: Friday, November 29, 2002 10:33 AM
> Subject: Re: [Yaesu] CAT FT990/FT1000 Problem: Clarifier Tuning
>
>
> > Something I would like to have is a remote knob for the FT1000 - a knob
> > which would adjust either (or both) the VFO and the RIT/Clarifier that I
> > could place along side the keyboard so I didn't have to touch the rig as
> > often would be great - allowing me to keep my hands on/near the
keyboard.
> >
> > A company called Eklektic (sp?) made such a know in mass quantities for
> > the Kenwood rigs and did a few special order units for Yaesu. They had
> > a remote tuning knob which could be changed to an RIT control with the
> > throw of a switch.
> >
> > In fast paced contest operating it is nice to not have to touch the rig
> > for long period of time while running however reality is that not
> > everyone calls on frequency - so there at least two times your hands
> > leave the keyboard - once to adjust the clarifier and once to undo the
> > adjustment to return top the "normal" frequency.
> >
> > I gather from this posting that the clarifier may be accessable from the
> > CAT jack - if this is so then maybe someone who is up on such things
> > could tell me if it is possible to construct a remote clarifier knob
> > form my 1000 without doing and serious work inside the rig - I do not
> > want to perform a modification to the rig itself if at all possible to
> > avoid such.
> >
> > 73, sorry for interrupting your QSO, Berndt!
> >
> > Jim, K4OJ
> >
> >
> >
> > wulf@ping.net.au wrote:
> >
> > >G'day,
> > >
> > >I experience problems setting the clarifier using the CAT interface.
> > >The following commands are function ok as expected:
> > >
> > >opcode | data1 | data2 | data3 | data4 | description
> > >--------------------------------------------------------------
> > >0x09 | 0x00 | 0x00 | 0x00 | 0x00 | RX clarifier disabled
> > >--------------------------------------------------------------
> > >0x09 | 0x01 | 0x00 | 0x00 | 0x00 | RX clarifier enabled
> > >--------------------------------------------------------------
> > >0x09 | 0x80 | 0x00 | 0x00 | 0x00 | TX clarifier disabled
> > >--------------------------------------------------------------
> > >0x09 | 0x81 | 0x00 | 0x00 | 0x00 | TX clarifier enabled
> > >--------------------------------------------------------------
> > >0x09 | 0xff | 0x00 | 0x00 | 0x00 | Clear Offset
> > >--------------------------------------------------------------
> > >
> > >However I can't seem to set the frequency using the following commands:
> > >
> > >--------------------------------------------------------------
> > >0x09 | 0x00 | 0x00 | 0x00 | 0x64 | Tune up 100 Hz
> > >--------------------------------------------------------------
> > >0x09 | 0x00 | 0xff | 0x00 | 0x64 | Tune down 100 Hz
> > >--------------------------------------------------------------
> > >
> > >Has anyone had success in setting the clarifier through the CAT
> interface?
> > >It almost looks as if the documentation omits some information needed
to
> > >do so, e.g. which value to set data1 when tuning the clarifier.
> > >
> > >I'm almost finished with programming a GUI that gives remote control
over
> a
> > >FT990 (FT1000 without dualband functionallity) and really like to get
the
> > >clarifier working too.
> > >
> > >There also seems to be no way in enabling the FAST dial function using
> > >the CAT interface, but this can be implemented in software.
> > >
> > >I welcome any ideas and hints!
> > >
> > >Many thanks in advance,
> > >
> > >73, Berndt
> > >VK5ABN
> > >_______________________________________________
> > >Yaesu mailing list
> > >Yaesu@contesting.com
> > >http://lists.contesting.com/mailman/listinfo/yaesu
> > >
> > >
> > >
> >
> >
> >
> > _______________________________________________
> > Yaesu mailing list
> > Yaesu@contesting.com
> > http://lists.contesting.com/mailman/listinfo/yaesu
> >
> >
>
>
> _______________________________________________
> Yaesu mailing list
> Yaesu@contesting.com
> http://lists.contesting.com/mailman/listinfo/yaesu
>
|