Yaesu
[Top] [All Lists]

Re: [Yaesu] FT1000MP original and FT8 setup

To: <yaesu@contesting.com>
Subject: Re: [Yaesu] FT1000MP original and FT8 setup
From: "David Robbins" <k1ttt@verizon.net>
Reply-to: k1ttt@arrl.net
Date: Wed, 12 Sep 2018 12:54:23 -0000
List-post: <mailto:yaesu@contesting.com>
Why not just use usb mode?  Works fine here!


David Robbins K1TTT
e-mail: mailto:k1ttt@arrl.net
web: http://wiki.k1ttt.net
AR-Cluster node: 145.69MHz or telnet://k1ttt.net:7373



-----Original Message-----
From: Yaesu [mailto:yaesu-bounces@contesting.com] On Behalf Of Mike Gilmer,
N2MG
Sent: Wednesday, September 12, 2018 12:24
To: yaesu@contesting.com
Subject: Re: [Yaesu] FT1000MP original and FT8 setup

I've seen that page (it seems everyone refers MP users to it) , but I have
problems with it.  For example - at the bottom - it says:

+++++++++++++++++++++++++++++++
**Early production original MPs did not allow TX Car to be set below
*456.300* Khz. but these values work fine.
.
.
.
TX CAR = *452.790*
+++++++++++++++++++++++++++++++

So, just how is an operator to set the TX CAR to 452.790 if MP's don't allow
one to go below 456.300?

73 Mike N2MG

On Tue, Sep 11, 2018 at 11:01 PM Dale Frederick <dale.kb5iy@gmail.com>
wrote:

> Ted, I'm not sure about the MP version of the 1000. Most of us non-MP 
> version ops are feeding the transmit signal into the MIC jack and 
> using USB mode.
>
> Someone did post http://www.tigertronics.com/ft1000mp.htm to the 
> FT-1000 Yahoo group, you might look at that.
>
> Dale KB5IY
>
>
> On 9/9/2018 9:18 AM, Ted Boerkamp wrote:
> > Hello...can anyone help me with the cabling requirements to get my
> FT1000MP
> > to transmit
> >
> > In FT8 mode?? I am also wondering if it might be similar to the 
> > PSK31 cabling using the Packet jack
> >
> > on the back?? I have a cable connected to transmit PSK31 already and 
> > it works.
> >
> > Do I need to set up another USER set of parameters for proper
> transmission
> > on USB??
> >
> >   I currently can receive FT8 no problem using WSJT but when I try 
> > to
> connect
> > to someone
> >
> > the PTT is activated but no power out.
> >
> > Any help or instructions would be appreciated. I have looked all 
> > over the net for such info but not
> >
> > finding very much specific to the FT1000MP original.
> >
> > Thanks
> >
> >
> >
> > Ted VE3SS
> >
> > _______________________________________________
> > Yaesu mailing list
> > Yaesu@contesting.com
> > http://lists.contesting.com/mailman/listinfo/yaesu
>
>
> _______________________________________________
> Yaesu mailing list
> Yaesu@contesting.com
> http://lists.contesting.com/mailman/listinfo/yaesu
>
_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu

_______________________________________________
Yaesu mailing list
Yaesu@contesting.com
http://lists.contesting.com/mailman/listinfo/yaesu

<Prev in Thread] Current Thread [Next in Thread>