No longer in production. Was the: Model 420 Hercules II Amplifier (500w), 160-10m, 65-80watts for 500w out, Solid State with eight (8) MRF458s as finals, 100% duty cycle, 13.5 volts $1395 . 73, Jim
Hi, TT has posted today both IP3 and Phase/Composite Noise data as measured in the Ten Tec labs by company engineers, see: http://www.tentec.com/TT565.htm For comparison with other rigs, see the tabu
The +5dBm spec is for the sub-rcvr; the curve shown is for the Main rcvr! Have a look at the page again, and you will see two lists of rcvr specs: the first for the main rcvr, the second list, where
Hi Tim, you wrote, in part: Good that you were able to obtain the pair together! For your comparison experiments, I would suggest that you use the external keyer for both rigs. Also, turn the Corsair
There was a time, several years ago, when many CW contesting stations were big into using the Kenwood TS-930S; that was in mid-80's I believe, just before the time of the Corsair, or perhaps, just a
Here is my exact experience and success using the Omni VI+, Henry amplifier and a QSK-5. Your problem is the difficulty in deciphering the Ameritron manual, hi. My use: my "fix" was to connect the ke
Correction to my previous post, re, SSB mode and the -5 unit in the system. Not sure that "hot switching" can be a problem in the SSB mode, but if so, my solution, I had written: I have not tried thi
Well, my Corsair II is on the bands everyday from out here in KH6 land. Anyone like to hear it, just let me know. I'll be using it, daily, UNTIL my new Orion arrives here on Kauai! 73, Jim KH7M
Some one wondered about using INRAD filters instead of the Ten Tec lattice filters. It has been suggested that Ten Tec's crystal lattice filters perform better than the INRAD filters for ultimate att
Yesterday I wrote, in part: 1. Ladder Filters I have been searching about for info on this topic. Lots of stuff out there about ladder filters, e.g.: http://www4.tpgi.com.au/users/ldbutler/LadderFilt
At last.... Tom, W8JI has begun to rebuild his web site. And one of the first posts he has put up is about key clicks with a discussion of "correct" rise and fall times and the overall wave shape. Th
I have a remote VFO for my Corsair II; is there any chance it will also act as a remote for a Triton 544? I know, weird idea, but maybe.....they are both PTO rigs after all, hi. 73, Jim KH7M
Hi, Am offering my RX-340 for $3000. I've had it just short of one year. But must sell to pay for my coming Orion, hi. If no one wants it now, I will ship it to TT for trade-in for partial pay for my
Was written: A couple of lines written by Doug Smith about the A/D conversion within the coming Ten Tec Orion rig: "State-of-the-art 24-bit IF-DSP converters, such as those used in the Ten-Tec Orion,
Hi, In the middle of the Hawaii Afternoon Net yesterday, my Pegasus QUIT. I happed to be net control Tuesday. I shut the set up down, and switched to the use of my Corsair II. Pegasus Symptoms: no op
Above is correct; and there is essentially zero propagation from KH6 to the mainland beyond California at that time of day on 20 meters, at this time of year and late morning out here. 73, Jim KH7M
Hi, In my Omni VI, the Key jack and PTT jack connect to a common line. Near as I can see, they go on to completely differing circuits in my Corsair II. Anyway, can I, without damaging anything, T con
The other day I asked: Rcvd no responses, so guess no one else was able to decipher the manual either, hi. Anyway, I went ahead and did tie the two together. Result: Seems to operate just fine in eit