Amps
[Top] [All Lists]

Fwd: [AMPS] Tuned input

To: <amps@contesting.com>
Subject: Fwd: [AMPS] Tuned input
From: ToddRoberts2001@aol.com (ToddRoberts2001@aol.com)
Date: Fri, 13 Jul 2001 08:16:58 EDT

--part1_e.f83f519.288040ba_boundary
Content-Type: text/plain; charset="US-ASCII"
Content-Transfer-Encoding: 7bit

Jim, I ran into a similar problem with a Dentron DTR-2000L linear amplifier. 
The DTR-2000L does not have a tuned-input circuit and was causing excessively 
high SWR when driven by my solid-state transceiver (Yaesu FT-840) . I built a 
small external pi-network tuned-input circuit using a double-pole rotary 
switch to switch in different value toroid inductors and fixed mica 
capacitors for each band in addition to 365pf air-variables permanently wired 
across the input and output sides of the circuit for fine-tuning. I used #2 
mix (red) toroids about 1" O.D. size and #18 magnet wire for each toroid. 
These will easily handle 100-150 watts of RF at the relatively low impedance 
levels for a tuned input circuit. The whole circuit is mounted inside a small 
aluminum mini-box and connected to the amplifier input thru a 1 ft length of 
RG-213 coax. The values for the toroids were fine-tuned after basing their 
values on a handbook article using the 8877 tube. This arrangement keeps both 
the exciter and amplifier happy. I recommend always keeping an SWR meter in 
line between the exciter and amplifier at all times to monitor the condition 
of match between the two, as well as a second SWR meter to monitor the output 
match to the amplifier. Hope this may help. 73 Todd Roberts WD4NGG .

--part1_e.f83f519.288040ba_boundary
Content-Type: message/rfc822
Content-Disposition: inline

Return-Path: <owner-amps@contesting.com>
Received: from  rly-yh03.mx.aol.com (rly-yh03.mail.aol.com [172.18.147.35]) by 
air-yh02.mail.aol.com (v78_r3.8) with ESMTP; Mon, 09 Jul 2001 13:10:07 -0400
Received: from  contesting.com (dayton.akorn.net [216.1.128.73]) by 
rly-yh03.mx.aol.com (v79.20) with ESMTP id MAILRELAYINYH32-0709130941; Mon, 09 
Jul 2001 13:09:41 -0400
Received: from dayton.akorn.net (dayton.akorn.net [216.1.128.73])
        by contesting.com (8.11.2/8.11.2) with SMTP id f69H9dW12110;
        Mon, 9 Jul 2001 13:09:39 -0400
Received: by dayton.akorn.net (TLB v0.10a (1.23 tibbs 1997/01/09 00:29:32)); 
Mon, 09 Jul 2001 13:09:28 -0400 (EDT)
To: <amps@contesting.com>
Date: Mon, 09 Jul 2001 13:09:16 EDT
From: Km8i@aol.com
Subject: [AMPS] Tuned input
To: <amps@contesting.com>
Mime-Version: 1.0
Content-Type: text/plain; charset=ISO-8859-1
Content-Transfer-Encoding: 7bit
X-Mailer: Unknown (No Version)
Message-ID: <16.f033544.287b3f3c@aol.com>
Sender: owner-amps@contesting.com
Precedence: bulk
X-Sponsor: W4AN, KM3T, N5KO & AD1C


A friend of mine recently purchased a Dentron MLA-2500.  In the archives I 
noticed some one had asked about this amp before, but I could not find the 
answer to this question.  Since the MLA-2500 does not have a tuned input what 
percautions are necessary to use it with a solid state rig.

As you can probaly guess I am not very familiar with amplifiers or their 
construction, but am planning to rectify that with some studying on the subject.

    TNX & 73,

      Jim KM8I

--
FAQ on WWW:               http://www.contesting.com/FAQ/amps
Submissions:              amps@contesting.com
Administrative requests:  amps-REQUEST@contesting.com
Problems:                 owner-amps@contesting.com


--part1_e.f83f519.288040ba_boundary--

--
FAQ on WWW:               http://www.contesting.com/FAQ/amps
Submissions:              amps@contesting.com
Administrative requests:  amps-REQUEST@contesting.com
Problems:                 owner-amps@contesting.com


<Prev in Thread] Current Thread [Next in Thread>