Ok, I will chime in here as the token rabid Dxer. 1.4 db can definately make a
difference in
certain situations. So consider me a cheerleader with respect to your "soup up
the amp" project.
Where does it stand now? How well does it work.
Michael
--- Richard <2@mail.vcnet.com> wrote:
>
>
> >Hi all,
> >
> >A few weeks ago, I mentioned that I had an AL80-A that I had modified for a
> >higher B+ voltage, mainly for the educational value. After putting it back
> >into service after a 7 yr hiatus, I had some fireworks and asked for
> >advice. I thank everyone who responded. That aspect has now been tamed. I
> >did some other mods, such as added a DC "brushless" fan in place of the AC
> >fan, which moves more air and is much quieter, but must be shielded from
> >the RF deck, lest it stop when I transmit.
> >
> ? Did you try bypassing + to at the DC input?
>
> >I hadn't had much chance to use the amp immediately after my mod, because I
> >relocated to Oklahoma from Colorado. So, I was fuzzy on its operating
> >characteristics. About all I recall is that, after the mod, I wasn't very
> >happy with it on the low ends of 160 m and 80 m, but that 75 m and all the
> >other bands seemed fine. The move, new job, and fresh biological harmonics
> >left little time for radio, and it, along with all my other
> >equipmentcollected dust .
> >
> >When I started this, about 7 years ago, that I fully realized that 1)
> >modifying perfectly fine, working commercial equipment is often a fool's
> >gambit, 2) raising the B+ from 2700 V to 3700 V (key-down) is pushing the
> >components to their limits, and 3) an extra 1000 V nets me only a nominal
> >1.4 dB increase in power output, which is of no practical
> >significance.
>
> ? amen to that, but don't mention this to a rabid DXer or he/she is
> likely to start frothing.
>
> > Yet, in the face of all that, I had the itch. I wanted to
> >*do* this, and see, hands-on, how all of this stuff works. I don't have the
> >tools, and only barely the metalworking skills, to fabricate the hardware
> >needed for a complete homebrew amplifier,
>
> ? The 20db, tetrode-with-handles amplifier on my Web site was built with
> a vise, a coping saw, a drill, a square and other basic hand tools.
>
> >and I don't have the
> >facilities. So, I was left with fixing stuff that ain't (yet) broke.
> >
> >After the mod, I knew that the output impedance of the 3-500Z would be
> >higher, but decided to "just see" how things went. Sure enough, all the
> >knob positions were different and I couldn't tune the amp well on the low
> >end of 80 and 160 m. It was as if I needed more tune and especially load
> >capacitance. Fiddling a bit with the equations and a simple program showed
> >me that the change in output impedance could not be easily ignored on the
> >low bands, especially.
> >
> >The output network (a Pi-L or L-L, take your choice) now had too high a
> >loaded Q (probably around 16-18 or so) and needed far more overall
> >capacitance because the inductance of the Pi part remained constant. I
> >guesstimated how much to move the taps to increase the inductance and bring
> >the loaded Q (and so capacitance requirements) back to a reasonable range
> >for the low bands (40 - 160) and everything worked great, except
> >160. There are no unused turns on the Pi inductor, so I had to add some.
> >Along the way, I found that the resistor in my parasitic suppressor had
> >been baked to a value of ~10 ohms, and so I replaced that.
> >
> ? more DC volts = more amplification. The most destructive parasite I
> ever encountered was at c.45MHz in a 12MHz 80kW PEP amp that ran enough
> anode V to make S9+15db X-rays.
>
> >...
>
> cheers, Kim
>
> - R. L. Measures, a.k.a. Rich..., 805.386.3734,AG6K,
> www.vcnet.com/measures.
> end
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
__________________________________________________
Do You Yahoo!?
Try FREE Yahoo! Mail - the world's greatest free email!
http://mail.yahoo.com/
|