Amps
[Top] [All Lists]

Re: [Amps] Power factor and choke vs resonant-choke input supplies

To: "Harold Mandel" <hmandel@barantelecom.com>,<g3rzp@g3rzp.wanadoo.co.uk>, "Borislav Trifonov" <bdt@shaw.ca>
Subject: Re: [Amps] Power factor and choke vs resonant-choke input supplies
From: "Barrie Smith" <barrie@centric.net>
Date: Thu, 10 May 2007 15:19:47 -0600
List-post: <mailto:amps@contesting.com>
----- Original Message ----- 
From: "Harold Mandel" <hmandel@barantelecom.com>
To: "Barrie Smith" <barrie@centric.net>; <g3rzp@g3rzp.wanadoo.co.uk>;
"Borislav Trifonov" <bdt@shaw.ca>
Cc: <amps@contesting.com>; <rbonner@qro.com>
Sent: Thursday, May 10, 2007 2:18 PM
Subject: RE: [Amps] Power factor and choke vs resonant-choke input supplies


Dear Barrie,

Now you have a project!

First thing: See if your choke winding has a  gap. That's the big ticket
hurdle, because without a gap, it can't swing.

Well, the choke and capacitor were purchased from Peter Dahl as a resonant
pair, so I would assume that the 9 hy choke was proper for the job.  I will
check it, none-the-less.

I was not aware that a resonant-choke was a swinging-choke.

Next, use your B&K LCR meter to measure the inductance. Can do, yes?

Yes.

Oh, well, no problem.

Build a rectifier out of some diodes and put some juice into the choke,
but make a
C-input filter with some small amount (2~4 uF) of capacitance and hook
up a load resistor
that will be more than the idle current you expect to crank.

Hook up an ammeter in the choke line. Turn the power off and put a
capacitor across the
choke leads. Lookit the amperage, write it down.

Start adding or substituting caps with lesser capacitance across that
choke puppy and
see where your jump in current occurs.

You could just hook up and do it without any juice at all, but that
won't give you
the dynamic performance point, which is always different than the
calculated
XsubC = XsubL point.

Anyway, send Tom Rauch an e-mail and ask him about testing chokes. (Har
de Har, Har, Alice!)

I have heard that story and I'm not looking forward to this experiment.

Be careful out there. The streets are a jungle.

Not as much so as my ham-shack.

73, Barrie, W7ALW

Hal
6L6GB

-----Original Message-----
From: Barrie Smith [mailto:barrie@centric.net]
Sent: Thursday, May 10, 2007 3:46 PM
To: g3rzp@g3rzp.wanadoo.co.uk; Borislav Trifonov; Harold Mandel
Cc: amps@contesting.com
Subject: Re: [Amps] Power factor and choke vs resonant-choke input
supplies

Peter:

Resonant-chokes may be placed in the negative lead?

Also, could you elaborate on the "close to it" resonance?

I have a largish power supply, using a Peter Dahl
resonant-choke/capacitor combination,  that has never worked properly.
I'd like to improve or rebuild the power supply so that it did work
properly.

73, Barrie, W7ALW


----- Original Message -----
From: "Peter Chadwick" <g3rzp@g3rzp.wanadoo.co.uk>
To: "Borislav Trifonov" <bdt@shaw.ca>; "Harold Mandel"
<hmandel@barantelecom.com>
Cc: <amps@contesting.com>
Sent: Thursday, May 10, 2007 10:34 AM
Subject: Re: [Amps] Power factor and choke vs resonant-choke input
supplies


> Why are you particularly worried abuot the power factor?
> Some simulations a colleague did some years back suggests that in
fact,
the choke shouldn't be resonant, but very close to it, such that the
choke
looks like a very much bigger inductance rather than a straight
resistance
at the ripple frequency. This is done for minimum load, as the choke
inductance will decrease somewhat as the load increases. That's how I
very
succesfully use tuned choke input: in addition, I filter in the negative
lead, so you don't need to worry about the case to innards insulation n
the
capacitor when it's reasonable size metal cased oil cap. Incidentally,
the
chokes were always obtained by a process f scrounging - I've never
bought
one yet! That includes a massive 10H 1 Amp one set aside for a
project....
> I believe Tom, W8JI, has some hair raising tales about his first
attempts
at resonant choke input supplies....
> 73
> Peter G3RZP
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>




_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>