I have the 2000C unit. and Carl I have to disagree with you about the Collins
influence. Ted Hunter worked for Collins and located his company just across
the city from Collins.. And my amp, has nearly the same color scheme...maybe
different circuitry, that may be the difference, dont know about that. :)
Tim
--- On Sat, 6/9/12, Carl <km1h@jeremy.mv.com> wrote:
From: Carl <km1h@jeremy.mv.com>
Subject: Re: [Amps] Hunter 2000c
To: "Tim Kass" <k8wbl@yahoo.com>, "Charles Hedrick" <cchedrick@gmail.com>,
amps@contesting.com
Date: Saturday, June 9, 2012, 8:38 AM
The Hunter 2000A and B were the 572 amps.
The C used a pair of 3-400Z's and was a very well designed and rugged kit with
quality components and on the market before the SB-220. There was no Collins
influence apparent.
While living in IL I operated at a contest station that had a pair of the B
models that held up well when not overdriven.
Carl
KM1H
----- Original Message -----
From: Tim Kass
To: Charles Hedrick ; amps@contesting.com ; Carl
Sent: Friday, June 08, 2012 10:37 PM
Subject: Re: [Amps] Hunter 2000c
It is a simple amp, doubt that both filaments would go out at the same
time..the transformer has all the windings on it, HV, filament, bias, so hope
its not your transformer.. had 2 of these in the past, still have one, my
primary amp, wonderful amp, built tough, similar to Collins since the designer
was an engineer at Collins before he started Hunter Electronics..
73, Tim K8WBL
--- On Fri, 6/8/12, Carl <km1h@jeremy.mv.com> wrote:
From: Carl <km1h@jeremy.mv.com>
Subject: Re: [Amps] Hunter 2000c
To: "Charles Hedrick" <cchedrick@gmail.com>, amps@contesting.com
Date: Friday, June 8, 2012, 7:39 PM
Start with the manual and follow the circuit, its a good but very basic amp.
Carl
KM1H
----- Original Message -----
From: "Charles Hedrick" <cchedrick@gmail.com>
To: <amps@contesting.com>
Sent: Friday, June 08, 2012 6:03 PM
Subject: [Amps] Hunter 2000c
> Hi all,
> We'll it was fine the day before yesterday, but last night I turned it on
> relays closed on xmit and no output. I looked and found the filaments
> were
> not glowing so suspect that circuit has an issue. I haven't put the
> beast
> on the bench yet, but has anyone experienced such an occurrence that can
> advise a starting place rather than a full circuit chase?
> Thanks
> WA4JKW
> Cam
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1424 / Virus Database: 2433/5056 - Release Date: 06/08/12
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1424 / Virus Database: 2433/5056 - Release Date: 06/08/12
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|