Amps
[Top] [All Lists]

Re: [Amps] Available Class A in Yaesu

To: amps@contesting.com
Subject: Re: [Amps] Available Class A in Yaesu
From: Alek Petkovic <vk6apk@bigpond.com>
Date: Sat, 18 Aug 2012 19:37:19 +0800
List-post: <amps@contesting.com">mailto:amps@contesting.com>
G'day Charles.

A small correction.

Do not run a Mark V in class A at less than 75 Watts full power. The 
extra dissipation in the finals when you run class A at reduced power, 
tips the BLF147's over the edge. The radio will run day and night at 75 
Watts out, class A. Ya wanna run class A, ya gotta run full grunt.

Most of us Mark V owners have learned this lesson, the hard way.

73, Alek
VK6APK


On 18/08/2012 7:22 PM, Charles Harpole wrote:
> Correction:  xcvrs with choice to xmit Class A are, at least, the following:  
> FT-1000MP Mark V, FT-9000Contest, FT-9000d, and FT-9000MP.  The latter three 
> also have a bias adjustment on the front panel to slide Class A downward away 
> from pure Class A in SSB or CW modes.  I burned up a Mark V by running it 
> full Class A (only choice on that rig) and at about 40 watts... great techs 
> tried to fix it and it blew two more sets of finals before I lost track of 
> it.  Morale, do not run a Mark V in Class A.  Today, I own K3f, FT-9000d, and 
> IC-7800, as well as KWM-2A, and several other rigs.  Very fun to compare 
> them.GL 73
>   
> Charles Harpole
> k4vud@hotmail.com
>   > From: jim.thom@telus.net
>> To: crc@cyberlink.bc.ca; amps@contesting.com
>> Date: Sat, 18 Aug 2012 00:09:29 -0700
>> Subject: [Amps] Re K3
>>
>>
>>
>> -----Original Message-----
>> From: Fern
>> Sent: Friday, August 17, 2012 9:11 PM
>> To: Jim Thomson ; amps@contesting.com
>> Subject: Re K3
>>
>> Jim:
>>        Where in the world are you getting your misinformation from re the K3?
>> You don't own one so quit running the darn radio down. Most of us ham don't
>> run any more than the legal power of 1500 watts so there's no need for a 200
>> watt exciter. I happen to have Icom, Kenwood and Yaesu rigs and by far, the
>> K3 has them all beat without a doubt. It would be nice if people would quit
>> running down equipment that they don't even own.
>>
>> ###  good info Fern.   Tell you what I will do.  I will  buy one next
>> week....with the
>> provisio if I don't like it,  I can get a full refund for it.   I'm getting
>> tired of one flop after
>> another after another for every xcvr that comes out.   I have yet to own any
>> of em, that work right,
>> designed right... outa the box.
>>
>> ##  since u have all the fancy test gear, do us all a favour and measure the
>> 2 tone TX imd at
>> 120 w pep out, ( or what ever max power on ssb is), and do it on all bands,
>> including warc.
>> Do it the correct way, not the arrl fubar method either.   IE:  db below one
>> tone of a 2 tone signal.
>> Then give us the results for imd 3-5-7-9-11-13.
>>
>> ##  while you are at it, measure the RX audio THD and max po of the k3's
>> audio section.
>>
>>
>>
>> I've been in the
>> communications business for over 50 years with owning my own business for
>> over 25 years so I think that I have a bit of an  idea as to what I'm
>> talking about as I have on my disposal all of the test equipment to check
>> this all out.
>>      The output power on the K3 is just over 120 watts dc (key down on mine)
>> not 100 W pep as you stated. 99% of legal hf amplifiers don't require any
>> more than 100 watts to drive them to full 1500 W allowed power. No offense
>> Jim, I'm just stating the facts.
>> Fern
>>
>> ###  allowed power is  2250 w pep... AFTER feed line loss.  IE:  measured at
>> the ant
>> feed point.  With just .5 db loss= 11% loss,  the amp has to put out 2528 w,
>> just to get
>> 2250 w pep at the feedpoint.   1db loss = 21% loss. Now we require 2850 w
>> out.... to
>> get 2250w at the ant.
>>
>> ##  I only have one grid driven amp here, (its being sold),
>> the rest are GG.   The hb 3x3  will do 2.5 kw pep out with real low
>> IMD..with just 100 w
>> pep  drive.  But that is a moot point if the xcvr is not up to snuff.   The
>> arrl lab tested
>> the k3 at -29 db pep  for IMD3.  That's  -23 db below one tone of a 2 tone
>> signal.
>> That doesn't meet any standard, ITU, mine, or anybody else's.
>>
>> ##  what's the point of me having an amp capable of -59 db pep for IMD3....
>> if I don't
>> have the mating clean  xcvr to drive it with.
>>
>> ##  fact is, a  55 year old  KWM2  will eat the k3  for breakfast, as far as
>> TX imd.
>> Your typ 200w  SS xcvr, when run at 100-120w pep out, is fairly clean.   The
>> only class A
>> 100 w pep out xcvr out there is the yaesu 400w version of the 9000.    And
>> even that xcvr
>> has enough problems.
>>
>> ## BTW, can you put the K3's  sub rx  on a different band than the main RX.
>>
>> Jim  VE7RF
>>
>>
>>
>>
>>
>> ----- Original Message -----
>> From: "Jim Thomson" <jim.thom@telus.net>
>> To: <amps@contesting.com>
>> Sent: Friday, August 17, 2012 7:57 PM
>> Subject: [Amps] K3 spike problem
>>
>>
>>> Date: Thu, 16 Aug 2012 14:11:02 -0700
>>> From: Jim Brown <jim@audiosystemsgroup.com>
>>> Subject: Re: [Amps] K3 spike problem
>>>
>>> On 8/16/2012 5:59 AM, Joe Subich, W4TV wrote:
>>>> In addition, if Charlie is using external ALC (he does not say) and
>>>> has the K3's power control set too high, he will see the spike due
>>>> to ALC time constants*in the amplifier*.
>>> It should be noted that when high quality rigs like the K3 are used to
>>> drive a power amp, amplifier output power should be set by using just
>>> enough drive power, NOT by setting drive power higher and using ALC to
>>> reduce it. For at least 30 years, Ten Tec has recommended AGAINST using
>>> ALC with their rigs and power amps in this manner. The only good reason
>>> for using ALC between a power amp and a transceiver is to protect the
>>> amp in case of a failure in the antenna system.
>>>
>>> ###  Unless the amp has a front panel adjustable ALC  control knob,
>>> it won't work anyway.  Also, the alc time constant in the  amp  HAS
>>> to match the alc time constant in the XCVR..and NONE of em do..
>>> so don't waste your time.
>>>
>>>
>>>
>>>
>>> In an excellent applications note on the topic, Tom, W8JI, noted that
>>> many rigs produce a spike of their full power output when their drive
>>> level is set well below full power. For those rigs Tom recommends a
>>> passive attenuator between the rig and the amplifier. The K3 is NOT one
>>> of those rigs -- indeed, it is quite well behaved. It's also one of the
>>> cleanest rigs on the air.
>>>
>>> ###  IOW, if the amp requires 50 watts of drive, then use a 3 db pad
>>> between
>>> the xcvr and amp, then run the xcvr at 100 w output.   IE: the pad is used
>>> to
>>> control the power output, and not any control in the amp.  If 25w drive
>>> required,
>>> then a 6db  pad is  required.  Any pad is a PITA.   The 3db pad has to be
>>> rated
>>> for at least 50 w CCS.   The 6 db pad has to be rated for at least  75
>>> watts CCS.
>>> Then you also lose   3-6db on RX... which is the last thing you want.
>>>
>>> ##  a simpler approach to adjustable po  is to just put -9vdc across a 50
>>> k
>>> pot...then feed 0-9 vdc (neg)   into the alc buss  on the xcvr.   Crank po
>>> control on xcvr to max... then adjust pot for desired output..from 0-max.
>>> No alc time constants to mess with,  since you have already developed the
>>> alc voltage  with your -9vdc source.   And no spike problem.
>>>
>>>
>>>
>>> ##  The K3 is NOT a clean xcvr on ssb.   It has typ lousy imd... like -29
>>> db pep
>>> for IMD3.   That's on a par with sweep tubes from the 70's.   It only does
>>> 100 w
>>> pep out, and I require a  200-250w pep put xcvr..so no K3 on my desk.
>>> Ten tec  needs to go back to the drawing board, and
>>> build a competitive xcvr.... not one that's  suited  for cw only + grid
>>> driven
>>> tetrodes.
>>>
>>> Jim  VE7RF
>>>
>>> 73, Jim K9YC
>>>
>>> _______________________________________________
>>>
>> π
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>                                       
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps

-- 
http://www.qrz.com/db/vk6apk
http://www.qrz.com/db/vk6ap

Family Businesses:
Petkovic Air & Gas. petkovicag@bigpond.com
SP Electrical. www.spelectrical.net.au
Hampers by Hand. www.facebook.com/hampersbyhand





=======
Email scanned by PC Tools - No viruses or spyware found.
(Email Guard: 9.0.0.2298, Virus/Spyware Database: 6.20420)
http://www.pctools.com/
=======
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>