Amps
[Top] [All Lists]

[Amps] Great Transformer Discussion!

To: <amps@contesting.com>
Subject: [Amps] Great Transformer Discussion!
From: "Jim Thomson" <jim.thom@telus.net>
Date: Tue, 23 Oct 2012 05:41:41 -0700
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Date: Mon, 22 Oct 2012 17:12:31 -0400
From: "Gary Smith" <Gary@ka1j.com>
To: Amps@contesting.com
Subject: Re: [Amps] Great Transformer Discussion!


>From a standpoint of reduced hum I like the idea of the interweaved 
terminal laminations (his E & I interweave description) as opposed to 
a pair of C cores with approximating tips. If his method will also 
give a higher CCS rating as Dhal used, and fit with the same 
dimensions, it would be worth looking deeper into.

There aren't that many transformer makers I know of any more.

Gary
KA1J

## A pair of C cores will blow away EI any day.   His plate xfmrs are not EI
per his website.  He has cut the ends of a c core differently so they inteweave.
Notice the big gaps with the spacers, when looking down on his plate xfmrs. 

The drawback to that approach is there is way less room on the core for the
windings.  On the old hypersil pole pigs, in oil, they used cut cores, but not 
interleaved.
But they did use ‘dogbone’ spacers to create gaps in the windings...to allow 
oil to
flow between the windings. 

He mentioned about the use of a 105 deg C temp rise....and presumably over 
ambient.
Now that’s bloody hot.  Most xfmr makers  spec temp rise over a 40 deg C ambient
when used in CCS mode.   105+40 = 145 C  =   293 deg F ! 

Dahl specs his plate xfmrs.. ( in CCS mode, 100% duty cycle)  at  55 deg C temp 
rise
over a 40 deg C ambient  + a further 10 C rise for spot heating deep inside the 
cores.
55+40+10 = 105 C    =   221 F       Big diff between  221 F  and 293F. 

Dahl does not go cheap on the temp rating of the insulation between windings.  
It’s
good for well over 175C  =   347 F. 

Its actually cheaper to make a xfmr with higher temp insulation and smaller ga 
wire
vs lower temp insulation + bigger ga wire.    Some dry typ xfmr makers... like 
for
vault xfmrs  used for 12.5 kv 3 phase down to 208/120 variety, will  run them 
blazing hot,
and I mean hot, no different than cracking your oven door open.   The better 
ones
will use a 50 deg C temp rise over  a 40 C ambient.    But some are as high as 
175 C
over a 40 C ambient.   Then you have everything between those 2 x extremes. 

You have to be real careful when spec’ing any xfmr.    I asked hammond for a 
quote
on a  custom built 7V  @ 80A  CCS  xfmr....and since I did not spec a temp rise 
over ambient,
they used a 60 C temp rise over ambient... which is blazing hot for a fil xfmr.

With the really big stuff, you also have another unique problem..and that’s 
your 240 vac
line will sag by 8-10 vac.   Your B+ regulation ends up not being what you 
would like, simply
cuz of the huge V drop from xfmr on the street, via the Aluminum drop wires to 
your home..
which are typ 2 x gauges smaller than the CU  wire they splice into at your pot 
head on
your home.   Hence you want pri taps at  225-230-235  even though your line V 
is 240 vac
with no load on it.   I got mine tapped at 198-208-218-230-240-250    His 
tapping scheme
is actually better, with 7 taps..and all 6 volts apart.  
240-234-228-222-216-210-204
What would be even better would be 240-235-230-225-220-215-210 

My dahl fil xfmr also came with 6 pri taps, same taps as my plate xfmr.   By 
juggling the various
pri taps on the plate xfmr with loads of sec taps, you end up with endless 
combo’s.   If you
folks ever buy a plate xfmr for a hb amp...get loads of pri and esp sec taps.  
Then at least u 
end up with a plate xfmr that will run anything and everything.   Drove me nuts 
using surplus xfmr
that were in perfect shape, but only had one sec V to use.... which was usually 
either too high...
or too low. 

later......... Jim  VE7RF 

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>