Don't forget to smear some aluminium jointing compound in the joint
between the grid flange of the YC156/YC179 and the raw aluminium
chassis. Electrolysis/corrosion sets in extremely quickly if you don't.
I discovered this when I was cooking some tubes with heater and fan
running for a few days. As I removed the tube from the burn in jig, the
start of corrosion was very evident.
73, Alek.
VK6APK
On 23/05/2017 9:58 PM, Thomas Walsh wrote:
Ditto on the yc-156 or better known ,as the
3cx5000A7, it will run on Ep of 3kv and higher,
at 25w in you get 1.5kw out, input imp.= 25ohms,
even the pulls from the mri world which only down
by a db or two will still produce 4-5kw out cw.
This means with 25w in and legal limit out, it is
really only idling! The bias is class AB and the
specs call for 1A idle current, that is for pulsed service with 10kv plate E,
but it runs just fine
with 500ma idle and much less plate E in cw mode, granted a little skewed on
the chart but only NCL's will bitch about this. It has fantastic imd specs at
full pwr, so with the greatly reduced power levels used in ham radio, it is
almost perfect!
And the best thing is - no socket to mess with!
Drill a 5.25 inch hole and you're done.
Tom,
W2CO
Sent from my iPad
On May 23, 2017, at 06:55, Jim Thomson<jim.thom@telus.net> wrote:
Date: Sun, 21 May 2017 10:07:13 -0400
From: "Carl"<km1h@jeremy.qozzy.com>
To: "Catherine James"<catherine.james@att.net>,
<amps@contesting.com>, "Jim Thomson"<jim.thom@telus.net>
Subject: Re: [Amps] new amp race
<A 2 el Shorty 40 isnt out of anyones capability as Cushcraft has proven for
<several decades and now more brands are available with decent performance as
<compared to the rotary dummy loads of the past.
<There are several 2500-3000 W amps on the used market using commonly
<available tubes and homebrew is still alive and well with the bigger Russian
<tubes as well as Eimac. The Chinese 3CX3000A7, built with Eimac supplied
<tooling, is a fine tube and a bargain in the $800 range. Use one of the 400W
<rigs or an AL-600 booster amp. A SB-200 works fine if 160 isnt requires.
<Bigger Eimac and European/Chinese tubes are readily available.
<Carl
## A 3CX-3000A7 is a superb bang for the buck, instant on too. 50 ohm input,
–59 db IMD3.
4 kw ccs anode dissipation. 225 watt CCS grid diss.
50 w in = 1.5 kw
100w = 2.5 kw
150w = 3.5 kw
200 = 5.1 kw
400 = 8.5 kw
## Its the ultimate...sleeper tube. Heres the ultimate blower for the 3x3
tube.
http://www.goldmine-elec-products.com/prodinfo.asp?number=G20814
Puts out 70 cfm @ 1.2 inches of water pressure. With that back pressure,
current
draw is only .4 amp from the 120 vac line. It uses an EC motor instead of an
AC motor or DC
motor. Variable speed is built in....using an external 10 K pot. Blower
doesnt even run luke warm.
Tube requires 67 cfm @ 1.2 inches of water pressure...@ 40 deg C inlet air
temp = 104 deg F.
Now you will never have 104 deg F in the shack, nor will you ever diss 225
watts of grid diss...so the
actual blower requirements are even less. The tube is essentially doing
nothing at 5-6 kw out, not even breaking
a sweat on rtty. Not bad for a tube that is only 4.94 inches in diam.
Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
--
From sunny Binningup
Our new house.
https://17coronation.wordpress.com
Family Businesses:
SP Electrical. www.spelectrical.net.au
The Velvet Fox. www.facebook.com/TheVelvetFox
Smart Design Electrical. 0417 602 032
Perth Interiors. https://www.instagram.com/perthinteriors/
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|