A quick note about distilled water: if the resistor gets hot enough to boil
water at its surface (regardless of the temperature of the water mass), the
steam will partially insulate the the resistor from its coolant, in which case
trouble will definitely ensue.
I’ve read that aviation turbine oil will do well, as will the already mentioned
drug store mineral oil.
Kim N5OP
"People that make music together cannot be enemies, at least as long as the
music lasts." -- Paul Hindemith
> On Feb 22, 2021, at 12:34 PM, Jim Barber <barberaudio@gmail.com> wrote:
>
> - or from Amazon.
> My wife buys it to fill snow globes and I use a little here and there:
> https://www.amazon.com/gp/product/B00VNI1JI0/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1
>
> My MRFX1K80N amp uses 90% distilled water and 10% propylene glycol. (pink
> RV antifreeze) Just enough to prevent algae from growing in the coolant.
>
> 73,
> Jim N7CXI
>
>
>> On Mon, Feb 22, 2021 at 9:27 AM Jeffrey L. Bauman via Amps <
>> amps@contesting.com> wrote:
>>
>> I have used mineral oil in my cantenna successfully as well.
>>
>> It's most cheaply sourced by the gallon from large animal veterinary
>> clinics
>> where it is used as a laxative and coat dressing.
>>
>> Good luck.
>>
>> Jeff
>> W8KZW
>> www.w8kzw.homestead.com
>> w8kzw@arrl.net
>> Davisburg, Michigan
>>
>>
>>
>> -----Original Message-----
>> From: Jim Klein [mailto:k7rdx@charter.net]
>> Sent: Sunday, February 21, 2021 8:08 PM
>> To: MU 4CX250B
>> Cc: Geert Jan de Groot; Amps group
>> Subject: Re: [Amps] Distilled water in a dummy load ?
>>
>> Palstar DL5K works well for me...No oil,fan cooled from
>> Palstar...Jim,K7RDX..
>>
>>> On Sun, Feb 21, 2021 at 12:46 PM MU 4CX250B <4cx250b@miamioh.edu> wrote:
>>>
>>> My instinct is that mineral oil would be a better coolant than
>>> distilled water, with no corrosion issues. You can buy it at any
>>> pharmacy, and while it isn't rated at quite as high a temperature as
>>> transformer oil, it works quite well. I used it in a Cantenna for 30
>>> years! As I recall, it was recommended byHeathkit as a substitute for
>>> transformer oil.
>>> 73,
>>> Jim w8zr
>>>
>>> Sent from my iPhone
>>>
>>>> On Feb 21, 2021, at 1:35 PM, Geert Jan de Groot <pe1hzg@xs4all.nl>
>>> wrote:
>>>>
>>>> ?
>>>>> Is it possible to use distilled water in a hb dummy load ?
>>>>> DL consist of 4 x 200 ohm globars, wired in parallel..in an 8
>>>>> gallon
>>> container.
>>>>> I welded 4 x 3 inch OD thick wall Alum pipes together, 2 stacked
>>> above 2.
>>>>> One resistor resides dead center in each alum pipe. Each resistor
>> is
>>> a
>>>>> new globar type SP, 12 inches long x 1 inch in diameter.
>>>>
>>>> Personally, I'm using the Ameritron ADL2500, which is 4 hefty
>>>> resistors
>>> in a case with a fan. I modified it so it automatically switches the
>>> fab to reduce the noise.
>>>>
>>>> No leakage, no corrosion, no mess if I drop it or I kick it. Much
>>> lighter. No dangerous oils, and my shack doesn't smell like a chip
>>> shop when I'm doing some testing.
>>>>
>>>> 73, Geert Jan PE1HZG
>>>>
>>>>
>>>> _______________________________________________
>>>> Amps mailing list
>>>> Amps@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/amps
>>> _______________________________________________
>>> Amps mailing list
>>> Amps@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/amps
>>>
>>
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|