about decade ago, read about method used at K3LR
started doing it LR way
Works!
http://www.k3lr.com/engineering/pl259/
Robert W5AJ
Midland, Texas
http://pages.suddenlink.net/w5aj/
-----Original Message-----
From: Amps [mailto:amps-bounces@contesting.com] On Behalf Of Jim
Sent: Thursday, April 08, 2021 8:37 PM
To: amps@contesting.com
Subject: Re: [Amps] Alpha 87A Won't Transmit
I've never had that issue in my 45 years of installing PL259s on Belden 8214.
Which is foam RG8.
Its called technique.
Thanks
73
Jim W7RY
On 4/8/2021 9:07 AM, gudguyham via Amps wrote:
> It’s nearly impossible to get a good solder connection on foam type coax. To
> do a good soldered pl259 you need to run the braid well so that soldering it
> to the shell makes a good connection to the braid. You’ll melt any foam when
> trying to probably tin the braid. However on poly type center conductor that
> can withstand the heat required to tin the braid you can effectively do a
> soldered connection to that type of coax and many hams like poly because it
> can be soldered. When I encounter foam coax I do crimp the braid but still
> solder the center conductor.
>
>
> Sent from the all new AOL app for iOS
>
>
> On Thursday, April 8, 2021, 9:45 AM, MU 4CX250B <4cx250b@miamioh.edu
> <mailto:4cx250b@miamioh.edu> > wrote:
>
> Thanks, Rob, that’s a very informative link. After years Of arguing
> against crimp connectors, I’ve finally been persuaded to change my
> mind. What did the trick are the “next generation” PL259 connectors
> sold by DX Engineering. I am gradually converting the hundred or so
> PL259 connectors in my station over to this design. The DXE connectors
> are a hybrid design that crimps the coax braid, but retains soldering
> for the center pin connection. Although they require a relatively
> expensive crimping tool, they can be installed in half the time as
> other connectors, and are virtually foolproof.
> 73,
> Jim W8ZR
>
> Sent from my iPhone
>
>> On Apr 8, 2021, at 4:45 AM, Rob Atkinson <ranchorobbo@gmail.com
>> <mailto:ranchorobbo@gmail.com> > wrote:
>>
>>
>>> In my experience, UHF connectors, especially spices, often develop
>>> corrosion and intermittent connections on the inner conductor. I’ve
>>> discovered that if I undo a PL259 and look at the mating S0239, I
>>> can clean a lot of carbonized goop out of the hole.
>> In my experience the problem is crappy off shore UHF females with pin
>> cups that don't tightly grip the male center. Read this:
>>
>> https://forums.qrz.com/index.php?threads/a-rogues-gallery-of-panel-mo
>> unt-uhf-jacks.735574/
>>
>> 73
>> Rob
>> K5UJ
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com <mailto:Amps@contesting.com>
>> http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps@contesting.com <mailto:Amps@contesting.com>
> http://lists.contesting.com/mailman/listinfo/amps
>
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com <mailto:Amps@contesting.com>
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com <mailto:Amps@contesting.com>
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|