CT-User
[Top] [All Lists]

[ct-user] CT 9.90.007 and Paddle

To: <ct-user@contesting.com>
Subject: [ct-user] CT 9.90.007 and Paddle
From: k1ep at arrl.net (Ed Parish K1EP)
Date: Thu Jun 26 20:24:06 2003
Don't even connect it to the radio to test.  Type SOUND to turn on the PC 
speaker and you will get sidetone from the PC.  That way you can check out your 
computer setup regardless of the radio.

>Hi David,
>
>Thanks for the response.
>
>This is my first attempt.  Running 5 watts into a dummy load.
>Wiring looks good.  Single dits and dahs work okay.  Putting
>them together creates garbage, after the initial good first
>letter.  Tried Super CMOS, Curtis A, and Curtis B modes with
>no difference.  Tried two different paddles with no difference.
>
>Was thinking about performing an exorcism.  8^)
>
>73,
>Bob
>
>----- Original Message ----- 
>From: "David Robbins K1TTT" <k1ttt@arrl.net>
>To: "reflector ct-user" <ct-user@contesting.com>
>Sent: Thursday, June 26, 2003 4:20 PM
>Subject: RE: [ct-user] CT 9.90.007 and Paddle
>
>
>> Check that you aren't getting rf into the port... turn off or reduce
>> radio power.  Doublecheck wiring and pin numbers, make sure no pins are
>> shorted and that pullup resistors are properly connected.  Slow the
>> speed way down and try to send single dits and dahs to see if maybe you
>> have bounce in a paddle contact.  Has it worked with earlier versions on
>> that machine or is this your first attempt??
>> 
>> 
>> David Robbins K1TTT
>> e-mail: mailto:k1ttt@arrl.net
>> web: http://www.k1ttt.net
>> AR-Cluster node: 145.69MHz or telnet://dxc.k1ttt.net
>>  
>> 
>> > -----Original Message-----
>> > From: ct-user-bounces@contesting.com [mailto:ct-user-
>> > bounces@contesting.com] On Behalf Of Bob Schreibmaier
>> > Sent: Thursday, June 26, 2003 20:00
>> > To: ct-user@contesting.com
>> > Subject: [ct-user] CT 9.90.007 and Paddle
>> > 
>> > I tried to use CT 9.90.007 and an external paddle on
>> > a Toshiba 486/50 laptop (QRP Field Day computer)
>> > running MS-DOS 6.22.  I used the REVPADDLE command
>> > to get the left paddle to send dits and the right
>> > to send dahs.
>> > 
>> > Sending with the motion necessary to send a "V",
>> > the first letter out is a "V", but the next one is an
>> > "F", followed by something unintelligible.
>> > 
>> > I've tried not using REVPADDLE, but simply changing
>> > the paddle around.  Same results.
>> > 
>> > Has anyone else seen this behavior?  Is it possible
>> > to fix?
>> > 
>> > TIA.
>> > 
>> > 73,
>> >     ____             /        _____           /
>> >    /    )           /        /               /
>> >   /____/   ____    /___     (____    ____   /___    /___
>> >  /     )  /    )  /    )         )  /      /    )  /
>> > /_____/  /____/  /____/    _____/  (____  /    /  /       . . .
>> > 
>> > +---------------------------------------------------+
>> > | Bob Schreibmaier K3PH | E-mail: k3ph@ptd.net      |
>> > | Kresgeville, PA 18333 | http://home.ptd.net/~k3ph |
>> > +---------------------------------------------------+
>> > 
>> > _______________________________________________
>> > CT-User mailing list
>> > CT-User@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/ct-user
>> 
>> 
>> 
>> _______________________________________________
>> CT-User mailing list
>> CT-User@contesting.com
>> http://lists.contesting.com/mailman/listinfo/ct-user
>> 
>
>_______________________________________________
>CT-User mailing list
>CT-User@contesting.com
>http://lists.contesting.com/mailman/listinfo/ct-user 


CONFIDENTIALITY NOTICE: This message is a PRIVATE communication. This email may 
contain privileged and confidential information intended only for the 
above-named 
recipient. If you have received this in error and you are not the intended
recipient, you are hereby notified that any use, dissemination, or copying is 
strictly prohibited. In such case, do not read, copy, or use it, and do not 
disclose 
it to others. Please notify the sender of the delivery error by replying to this
message, and then delete it from your system. Thank you. 



<Prev in Thread] Current Thread [Next in Thread>