Karlnet
[Top] [All Lists]

Re: [Karlnet] routing question

To: "Karlnet Mailing List" <karlnet@wispnotes.com>
Subject: Re: [Karlnet] routing question
From: "wesley allison" <scgn@pipeline.com>
Reply-to: wesley allison <scgn@pipeline.com>, Karlnet Mailing List<karlnet@WISPNotes.com>
Date: Wed, 2 Jul 2003 18:27:21 -0500
List-post: <mailto:karlnet@WISPNotes.com>
Ok, I think I have narrowed this down to my AP-1000. I have a router hook to
the internet with a live IP, this router is using NAT to give me 192.168.0.X
private address with 192.168.0.1 being the gateway address. I have my
AP-1000 hooked to this router and a few clients spread around the house. I
have set the clients up and they can ping all the way back to the AP-1000
but not out to the internet. I do not have NAT turned on at any of the
client stations or the AP-1000 and everyone is set in route mode not bridge.
I am stuck and I am sure it is the one big tree in my face that is the
reason I am unable to see the forest. I am sure if someone as example of a
similar setup I will see my mistake.

wes
----- Original Message ----- 
From: "Darko Delic" <darko@tradal.net>
To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Sent: Wednesday, July 02, 2003 2:02 AM
Subject: Re: [Karlnet] routing question


> Hello,
>
> First of all, what do you mean by "to route out to the internet to hold
> down on broadcast" ???
>
> Are you using NAT on AP-1000 since in your example you stated that you
> use private IPs which are not routeable outside your network ?
>
> It would be good if you can send output of ip routes from configurator.
>
>
> On Tue, 2003-07-01 at 18:27, wesley allison wrote:
> > I just received all my equipment and Karlnet software and I am in the
> > process of getting things squared away. I have setup my AP-1000 as a
base
> > station and my RG-1000 as a satellite. I have decided to route from my
cpe
> > to the base station and out to the internet to hold down on broadcast
> > traffic. I am having a problem getting to the internet from my CPE. I
can
> > ping all the way back to the base station, but I can't get to the
internet.
> > I do have my Base setup as a bridge at this point but I have tried it
both
> > ways and I seem to get blocked at the base station. The way I would like
to
> > do it is at the CPE I run DHCP on the Ethernet connection and route that
> > traffic to the wireless interface, then from that wireless interface to
the
> > base station wireless interface, then to the base station Ethernet
interface
> > and out on the internet and back. So I was checking to see if anybody
had
> > any suggestions. "quick note everything works fine in bridge mode all
the
> > way from the cpe to the internet, so the equipment is working fine."
> >
> > example
> > 10.10.10.1 -----> 192.168.1.10        RG-1000 hooked to client computer
> > cpe Ethernet        cpe wireless
> >
> > 192.168.1.10 ------> 192.168.1.5    RG-1000 connected to AP-1000 base
> > station
> > cpe wireless                 base wireless
> >
> > 192.168.1.5--------> 192.168.1.1    AP-1000 base station connected to
> > internet connection
> > base wireless            internet
> >
> > Thanks
> >
> > wes
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> -- 
> Darko Delic <darko@tradal.net>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet

<Prev in Thread] Current Thread [Next in Thread>