hmm... what kind of radios are you running in your AP1000? I've heard that
the Prism cards can cause an AP1000 to overheat but stock 35mw Lucent cards
shouldn't cause much heat build-up.
----- Original Message -----
From: "wesley allison" <scgn@pipeline.com>
To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Sent: Tuesday, September 02, 2003 6:33 PM
Subject: Re: [Karlnet] antenna problem
> sorry recheck and it is 12 volts
>
> ----- Original Message -----
> From: "Larry Yunker (Cyber Broadcasting)" <leyunker@cbcast.com>
> To: "wesley allison" <scgn@pipeline.com>; "Karlnet Mailing List"
> <karlnet@WISPNotes.com>
> Sent: Tuesday, September 02, 2003 4:12 PM
> Subject: Re: [Karlnet] antenna problem
>
>
> > 50 VOLTS?? Uhh... My hyperlink amps take 12V power supplies, if yours is
> > similar, you shouldn't be pushing 50VOLTS!
> >
> > ----- Original Message -----
> > From: "wesley allison" <scgn@pipeline.com>
> > To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
> > Sent: Tuesday, September 02, 2003 3:07 PM
> > Subject: Re: [Karlnet] antenna problem
> >
> >
> > > checked the injector and no voltage on the radio side and 50 some
volts
> dc
> > > on the other side. Thanks for the suggestion.
> > >
> > > wes
> > > ----- Original Message -----
> > > From: "Roger Boggs" <rogerboggs@att.net>
> > > To: "wesley allison" <scgn@pipeline.com>; "Karlnet Mailing List"
> > > <karlnet@WISPNotes.com>
> > > Sent: Tuesday, September 02, 2003 1:34 PM
> > > Subject: Re: [Karlnet] antenna problem
> > >
> > >
> > > > Bad power injector? Disconnect the injector from the AP and measure
> DC
> > > voltage
> > > > across center conductor and shield - CAREFULLY, of course.
Shouldn't
> be
> > > any
> > > > power supply voltage showing there. It should only show on the amp
> side
> > > of the
> > > > injector.
> > > >
> > > > At 01:25 PM 9/2/03 -0500, you wrote:
> > > > >I have an antenna problem that I was wondering if anybody else has
> had
> > or
> > > > >heard of? I have an AP-1000 hooked up to a hyperlink amp running up
a
> > > tower
> > > > >about 150 feet to a omni antenna. When we hook up the amp the
AP-1000
> > > over
> > > > >heats. I have checked all the connections to make sure that we are
> not
> > > > >backwards and I can't figure out what is going on, this amp is not
> > rocket
> > > > >science. Any ideals
> > > > >
> > > > >wes
> > > >
> > > > Roger Boggs
> > > >
> > > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > >
> >
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
|