Hi Tod, K0TO,
I have a Radar Engineers Model 240 which I use for locating noise sources on
power lines. I highly recommend it. I also have a Radar Engineers Model 250
Ultrasonic Locator. The combination can not only find the offending pole, but
usually I can pick out the noise making hardware while remaining on the ground.
I like to use my Tektronix Model TDS-210 Oscilloscope with the 240, larger
display and easier to see. I run the scope off of an Astron Model Pi-250W power
inverter. It has a remarkably accurate crystal controlled frequency. This allows
synchronization with the power line frequency.
Normally I use a two or three element beam on 144 MHz to locate the "suspect"
pole with the 240, then I use a 440 MHz 6 element yagi to verify the pole, and
finally I use the 250 to pick out the hardware item on the pole. The Model 240
really is an outstanding piece of equipment, as is the 250.
You can read a story I wrote about my locating experience in Marv Loftness' new
edition of his AC Power Interference Handbook, available from the ARRL. Marv's
book is a "must read" for information on how to locate power line noise sources.
I hope this helps you. If you have any questions, but email me.
Sincerely, and 73s,
>From email@example.com Mon Aug 11 23:31:42 2003
Received: from ms-smtp-03.tampabay.rr.com (ms-smtp-03.tampabay.rr.com
by contesting.com (8.12.9/8.12.9) with ESMTP id h7C3Vagq019598
for <firstname.lastname@example.org>; Mon, 11 Aug 2003 23:31:42 -0400
Received: from tampabay.rr.com (6535181hfc121.tampabay.rr.com [22.214.171.124])
h7C3VQ4W028465; Mon, 11 Aug 2003 23:31:34 -0400 (EDT)
Date: Mon, 11 Aug 2003 23:32:15 -0400
From: "Jim White, K4OJ" <email@example.com>
User-Agent: Mozilla/5.0 (Windows; U; Win98; en-US;
rv:1.0.2) Gecko/20030208 Netscape/7.02
X-Accept-Language: en-us, en
Subject: Re: [TowerTalk] Reverse rotation on Ham IV
Content-Type: text/plain; charset=us-ascii; format=flowed
List-Id: Tower and HF antenna construction topics. <towertalk.contesting.com>
X-List-Received-Date: Tue, 12 Aug 2003 03:31:42 -0000
one should stay one....
that is your system common for both the directional and brake "paths"....
unfortunately my manual is not here but....
I know 4 and 8 are the motor capacitor....
so I would guess it just may be 2 and 3 that need switching....
Lift the line and put you Voltmeter on there - see which combo moves
when you hit the directional buttons!
As memory serves its 24 volts I think
> I think I goofed somewhere with control cables (too many connectors and
> too many splices) to the rotor and the rotor is rotaiting the other way.
> When I press CW it rotate CCW. It is like CW and CCW are reversed. What
> happen if I reverse wires connected to pin 1 and 2? Will the rotor rotate
> the way it
> Andy - VA3PL
> See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
> Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
> questions and ask for Sherman, W2FLA.
> TowerTalk mailing list