Sure, but somebody has to get the ball rolling. You sound like you have
the motivation. Nothing to stop you fromworking with the guy in the
meantime. You could even buy a starter set of the same lights and
figure out what's needed in the way of bypasses and ferrites, and then
take the set back to Lowe's or wherever. If you figured out a relatively
affordable and workable fix, I bet a lot of people would be grateful.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 3/12/2013 8:44 AM, Mike Ryan wrote:
Thanks for the big picture. But aside from driving over the guy's
lawn and taking out the lights with a couple of figure '8s', the
question is how to get rid of the noise.
-m
-----Original Message----- From: Pete Smith N4ZR
Sent: Tuesday, March 12, 2013 6:46 AM
To: rfi@contesting.com
Subject: Re: [RFI] Cree LED Bulbs?
Scrood indeed, but the good news is that Lowes and Home Depot (if they
are carrying the same type) may be big enough to be susceptible to
pressure. What these systems are doing is contrary to FCC regs, and the
RFI people at ARRL HQ (Ed Hare, W1RFI, is very knowledgeable) may be
willing to get involved. A few years ago, they scored a notable success
by getting the makes of the Homeplug LAN hardware to notch out the ham
bands.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 3/12/2013 12:27 AM, Mike Ryan wrote:
The box that these lights come in from Lowes says they are LED
lights. I bought one today and I am sending it to a friend to take a
look at along with a power supply. He wants to look it over to see
what can be done. But for now it appears that I am scr...d, blued,
and tatooed.
-M
-----Original Message----- From: Dale
Sent: Tuesday, March 12, 2013 12:21 AM
To: ka5s@earthlink.net ; rfi@contesting.com
Subject: Re: [RFI] Cree LED Bulbs?
Cortland, Mike, Kurt, and All,
If you go back to my post of a few days ago, it sounds as if I may
have scored a direct hit (by dumb accident) on this system; after
careful reading of Mike's information, it does sound like the
manufacturer is using a simple, iron core transformer to go from 120
VAC to 12 VAC. That's the good news.
Now, one thing I have not seen Mike comment on is if the devices
inside those lamp heads are bulbs or LEDs. If they are LEDs, I can
tell you that there are several manufacturers out there making
specialized ICs that serve as the constant current controllers for
LEDs. If they are bulbs, then I agree with Kurt's comments about
bulbs not caring if they get AC or DC. Either way, the picture I am
getting is that we have a low voltage, relatively high current wired
distribution system that goes from the step-down transformer to the
individual lamp heads. The problem may well then be what's inside
those heads, particularly if the lighting devices are LEDs.
Since cost is always THE driver these days (sad, but true), I can
tell you that I have been shocked by the number of app notes I have
seen from the LED constant current guys about circuits to use their
ships and in which there is little or even NO suppression of
switching noise on the input side of the device. Some of these chips
are meant to run on low voltage AC input, and then the constant
current controiller is a specialized switcher that outputs DC to the
LEDs. So, the bad news is that my "guess" about each lamp head
containing a small switcher might be correct. If it is, wow - what a
mess!
-----Original Message-----
From: Cortland Richmond <ka5s@earthlink.net>
Sent: Mar 11, 2013 9:21 PM
To: rfi@contesting.com
Subject: Re: [RFI] Cree LED Bulbs?
On 3/11/2013 2125, Cortland Richmond wrote:
On 3/11/2013 1952, Mike Ryan wrote:
The landscaping lights turn out to be 12 volt AC powered and not 12
volt DC powered. All the suggestions about a car battery and/or an
Astron or other linear power supply now go out the window. -M
But the converter is still very likely a switch-type converter;
modern-day efficiency rules often rule out transformers on account of
core losses.
Cortland Richmond
KA5S
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
And even if it does use a linear 12VAC transformer, the LED's
themselves
require a constant current source -- and probably incorporate switching
regulators at each fixture. Have you contacted the system maker?
Cortland
KA5S
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|