Hi, Martin. David/K1TTT also have very valid points about signal egress and
ingress among various components in the RF path. The signals sometimes are a
challenge to contain them to the signal path.
As for shields over a foil braid, two different situations can occur. One is a
broadband noise that raises the noise floor generally, which is not what you
are currently describing. Any movement of the braid/foil cables probably will
generate this noise when a transmitter is active, especially if it’s in the RF
path. Initially, this condition may not be present, but over time, it’s very
likely to appear.
The braid against the foil oxidizes and creates the non-linear junctions you
are familiar with from your VHF experiences. If not a broadband noise, it can
be a source for generating rich harmonics external to the intended suppression
techniques you are installing.
Also, any “loose” antenna parts are a prime source of PIM. All metal to metal
connections need to be tight and a anti-oxidation grease applied to minimize
the PIM potential.
I feel your pain about adding a second transmitter to what “appeared” to be a
perfectly working single transmitter station. In the Georgia QSO Party for the
past 5 years, we have been running a Multi-2 Rover station while in motion for
900 miles across 20 hours over 2 days. The two mobile antennas are 5 feet
apart. I’ve bonded every body part and purpose built two stout frame antenna
attachment pods. Even still, when we go over a rough bump, there will be a blip
of broadband noise from some vehicle metal to metal junction. We have found
several HF mobile antennas that work great by themselves, but are significant
broadband noise generators in a Multi-2 situation.
Keep hammering away at it. You are on the right track.
Mike / W5JR
Alpharetta GA
On Nov 21, 2019, at 6:00 AM, Martin Sole <hs0zed@gmail.com> wrote:
Dear Jim and Mike,
Thanks very much for the prompt replies.
Jim, I think the chokes are either from your latest work using big 31 rings or
from the design by GM3SEK using multiple big beads and with I believe at least
two such chokes in series. That is for each of the feeds to the antennas. The
chokes are placed just slightly before the Array solution balun, again one at
each feed point. I will review your other document as well, I can see it
references issues similar to that which I have observed first hand. Yes the
harmonic DOES have a growl to it!
The cable is predominantly 1/2" heliax of various manufacturer, based on what
is available in country but all used in pro installations so generally decent
stuff. There is some RG214 and some may have a foil. I do know that some of the
stubs and their associated coupling cables I prepared are made with an RG214
that has 2 braids plus a foil and a dielectric that has 0.8v.f.
If foil and braid coax is used what is the issue?
Is there a PIM risk between the braid and the foil?
I am familiar with PIM having seen it first hand at VHF though it was always
true intermod, being two incident signals creating a third order product.
Though in those cases we never considered or cared about harmonics, for other
reasons, I can agree that the non linear device should indeed produce all
possible products including harmonics of a single source.
Regards es tnx
Martin, HS0ZED
> On 21/11/2019 12:40, Mike - W5JR wrote:
> If any of the “RG214” is in fact a shield over foil braid, replace it with
> real RG214. As Jim mentions, passive intermod (PIM) usually rears its ugly
> head after installation of all the cool stuff. You will want to confirm that
> all of the components, radios, amplifiers, filters, feedlines, towers, guy
> systems, are *bonded* together to further reduce the possibility of PIM.
>
> PIM will be the biggest hurdle in making any multi transmitter situation play
> nice. Often the PIM generator is external to your feedline or antenna. It’s
> the “killjoy” of many a Field Day setup over here.
>
>
> tnx
> Mike / W5JR
> Alpharetta GA
>
>
> On 21/11/2019 11:52, Jim Brown wrote:
> Hi Martin,
>
> here's an "overview" talk that I've done at Visalia last spring and for a
> couple of clubs, including NCCC, this fall.
>
> http://k9yc.com/Multi-Station.pdf
>
> Among other things, check out the chokes in my newest Cookbook, which are
> significantly better and more repeatable designs than what I was able to do
> 10 years earlier.
>
> Also, consider passive intermod.
>
> 73, Jim K9YC
>
>
>> On 11/20/2019 8:22 PM, Martin Sole wrote:
>> Hi,
>>
>> This is about a two radio inter-station interference problem. A bit
>> different perhaps but still RFI of a sort
>> Looking for some input to help me understand a bit better what is happening
>> and maybe correct some errors in my thinking.
>
> _______________________________________________
> RFI mailing list
> RFI@contesting.com
> http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|