That is exactly what Tom, W8JI told me almost 40 years ago.
73, Pete - N8TR
At 05:44 PM 8/16/2021, donovanf@erols.com wrote:
When its no longer under pressure and protected from moisture
the RF resistance of braid goes up dramatically because the
crossovers in the braid no longer conduct effectively.
That's why the appropriate choice for an outdoor conductor is
stranded wire or solid wire and never braid
73
Frank
W3LPL
----- Original Message -----
From: "K9MA" <k9ma@sdellington.us>
To: donovanf@erols.com, rfi@contesting.com
Sent: Monday, August 16, 2021 9:27:16 PM
Subject: Re: [RFI] DFing intermittent connection
Gee, it's worked for me for years. Not much salt spray in Wisconsin.
73,
Scott K9MA
On 8/16/2021 12:32 PM, donovanf@erols.com wrote:
Jim,
Please ignore Scott's advice, it will cause tower corrosion and quickly fail
73
Frank
W3LPL
----- Original Message -----
From: "K9MA" <k9ma@sdellington.us>
To: jimk8mr@aol.com
Cc: rfi@contesting.com
Sent: Monday, August 16, 2021 4:30:35 PM
Subject: Re: [RFI] DFing intermittent connection
Or just use the braid from some RG8 and a couple hose clamps.
----------
Scott Ellington. K9MA
--- via iPhone
> On Aug 16, 2021, at 9:27 AM, jimk8mr--- via RFI
<rfi@contesting.com> wrote:
>
> The kit is basically a very heavy, very flexible cable, six feet
or so, with lugs on both ends, and clamps with a large flat surface
to attach to the mast and to the tower leg. I'd think that the
bottom lug could be attached to a tower bolt, or some other low
resistance connection to the tower.
> It would seem to also be simple to homebrew something a bit less
rugged, perhaps using a piece of RG-8, shield and center conductor
connected together.
>
> 73 - Jim K8MR
>
>
>
> -----Original Message-----
> From: EDWARDS, EDDIE J via RFI <rfi@contesting.com>
> To: RFI List <rfi@contesting.com>
> Sent: Mon, Aug 16, 2021 9:09 am
> Subject: Re: [RFI] DFing intermittent connection
>
> Just FYi...They told me they only have the bypass kits for
standard Rohn towers, but not for the BX or HDBX series towers.
Need to make your own for other non-rohn configurations.
>
> 73, de ed -K0iL
>
> -----Original Message-----
> From: RFI On Behalf Of jimk8mr--- via RFI
>
>
> You might look into DX Engineering's Bearing Bypass Ground Kits
DXE-BBGK-2-25-P.
> I installed one yesterday for K8AZ. I'm not sure if Tom had a
particular problem or it was just as a precaution. It easy to
install, the only issue in my case was that the tower had been
painted, so some paint scraping was in order. But much easier than
replacing a thrust bearing!
>
> 73 - Jim K8MR
>
> _______________________________________________
> RFI mailing list
> RFI@contesting.com
> http://lists.contesting.com/mailman/listinfo/rfi
> _______________________________________________
> RFI mailing list
> RFI@contesting.com
> http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
--
Scott K9MA k9ma@sdellington.us
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|