RTTY
[Top] [All Lists]

Re: [RTTY] Rig Blaster Pro + Kenwood TS 2000

To: rtty@contesting.com
Subject: Re: [RTTY] Rig Blaster Pro + Kenwood TS 2000
From: ea8auw@cidxs.com
Date: Mon, 4 Feb 2008 01:44:08 +0100 (CET)
List-post: <mailto:rtty@contesting.com>
Hello again Bob K0RC, Don AA5AU and everyone !

Thanks you very much for your interest answer for me.

Don, If I have also the EXTFSK with the MMTTY from any JA stations, not
remember well his callsing,and I made well the configuration this
afternoon with TXD and DTR. I'm forget to say it that I use also the
EXTFSK program.

Well, now I have PTT continued but I haven't RTTY sound in the out.

The P16 jumpers of the rig blaster pro I don't touched because in the
manual I can't see any configuration for Kenwood radios, probably this
it's the problem, Tomorrow I want to try play with this jumpers for any
good FSK configuration, The rest of the configuration of cables and of the
program I think it's OK, bacause  I cheking this config. several times.

I think that the P16 Jumpers it's the way for running in RTTY, I have
verified everything even almost madman turned me, hihi....

Thanks you very much Don and Bob for his help, Whem I testing the P16 I
write you for to say it if running well or if I have others problems.

Big 73 DR OM de Edu EA8AUW
PD. Excuse me for my english lenguage not it's 100% correct, But I hope
you stand me. bye!

> Sounds like the PTT output of the Rigblaster getting the FSK signals from
> the computer and keying the radio on and off in sequence
> with the Baudot being sent.
>
> I'm not familiar with either the RigBlaster PRO or the TS-2000 but have
> looked at the manuals.  Make sure the RigBlaster is set up
> to use TxD for FSK and RTS for PTT.  This is the standard setup.  If you
> need to use other pins on the RS-232 output of the
> computer, you will need to use EXTFSK with MMTTY.  For instance, if you
> want to key FSK with DTR, then you must use EXTFSK.
>
> For FSK the TS-2000 input is on pins 2 and 4 of ACC2 so it appears you
> have this connection correct.  It sounds like you need to
> change the P16 jumpers in the RigBlaster so that FSK is on TxD.
>
> 73, Don AA5AU
> http://www.aa5au.com
> http://www.rttycontesting.com
>
> -----Original Message-----
> From: rtty-bounces@contesting.com [mailto:rtty-bounces@contesting.com] On
> Behalf Of ea8auw@cidxs.com
> Sent: Sunday, February 03, 2008 10:59 AM
> To: rtty@contesting.com
> Subject: [RTTY] Rig Blaster Pro + Kenwood TS 2000
>
> Hello Everybody !
>
> I have a Rig Blaster Pro + Wintest + MMTTY engine connected to my Kenwood
> TS 2000.
>
> The transmition not it's good, the PTT connect it and it is disconnected
> very rapidly, many times like CW Mode in possibly like
> semi-full break configuration.
>
> I connect the radio to Rig BP to slant of ACC2 port (DIN 13 pins):
> Pin Nr. 2 and Pin 4 GND  to the mini Jack of Rig BP FSK out.
> Pin Nr. 3 to Audio In of Rig Blaster Pro and to the same GND, I think now
> Pin 4 the same GND that the FSK In of my radio.
>
> But the RIG and Radio connect and disconnect it very time continued.
>
> Has someone had this problem ??
>
> any help it's wellcome.....
>
> Big 73 from Edu EA8AUW
>
>
>
> _______________________________________________
> RTTY mailing list
> RTTY@contesting.com
> http://lists.contesting.com/mailman/listinfo/rtty
>
>


_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty

<Prev in Thread] Current Thread [Next in Thread>