Comments/answers in-line below.
Figured I'd start here.
Want to play in 75-baud BARTG tomorrow. Have a new Rigexpert TI5
which supports FSK. The problem is that the TI5 uses different fake
com ports for PTT and FSK. It does this by hacking EXTFSK, the DLL
that comes with MMTTY.
I believe you have stated this backwards. As I read the manual, the TI5
uses different virtual COM ports for CAT, PTT, Winkey and FSK without
EXTFSK. I believe the reason RE included the hacked version of EXTFSK
with the TI5 is to support software that must use the same port for PTT
and FSK. This is not a problem if you are using the N1MM Logger/MMTTY
combination, because you can do PTT from N1MM Logger and FSK from MMTTY
on separate ports, thereby avoiding the need to use EXTFSK.
And RE didn't hack EXTFSK (as far as I can
tell - the windows doesn't pop up with the hacked version) to support
75 bauds.
As I understand it, the reason EXTFSK doesn't support 75 baud is because
of unacceptably large (for 75 baud) timing jitter with the method EXTFSK
uses. EXTFSK is a method of last resort, to be used only if you have no
alternative. Frankly, if you take a reasonable amount of care with sound
card settings, I think AFSK is preferable to EXTFSK.
I run N1MM with the MMTTY engine though in this case, I don't know if
that makes a difference.
Yes - it means you can use the separate ports for PTT and FSK without
resorting to EXTFSK. If the TI5 driver uses COM3 for CAT, COM4 for PTT,
COM5 for Winkey and COM6 for FSK, for example, you can configure N1MM
Logger to use COM3 for radio control, COM4 for PTT on RTS, COM5 for CW
using the Winkey, and COM6 as the digital port, configured in MMTTY for FSK.
Would it be possible to set the "PTT & FSK" setting in MMTTY to the
FSK port (COM10 here) and then use the "Radio Command" setting?
No. The radio command (CAT) port is in use by N1MM Logger for radio
control. MMTTY does not have access to it.
Or
are they tied together somehow?
If you are using MMTTY stand-alone, it uses the same port for PTT and
FSK. Even when run under N1MM Logger, MMTTY will send commands to toggle
RTS and DTR on its FSK port for PTT, but as I understand it the TI5 will
simply ignore those commands. You should configure N1MM Logger to
control PTT using RTS on the TI5's PTT port (RE calls this the
PTT/CW/SoftFSK port, but the only thing you need to use it for is PTT).
One issue you may run into is the timing of PTT. The transfer of data
over the USB cable is much faster than the actual transmission, and with
some setups that can result in PTT turning off before the data has
finished being transmitted. With any USB-based device, in the MMTTY
Setup window you should click on the USB Port button beside the
COM-TxD(FSK) selection under the Misc tab, and select C. Limiting Speed.
And, yes, like my old RigBlaster+, I have to fiddle with a jumper in
the RE ... (I haven't ordered the reed switches yet).
In addition to the baud rate jumper in the TI5, you will also have to
set up MMTTY to receive 75 baud. See
<http://n1mm.hamdocs.com/tiki-index.php?page=Digital+-+MMTTY+for+RTTY+Support&structure=N1MM+Logger+Documentation#Using_MMTTY_for_75_baud_RTTY>
for some of the things to look out for.
Anyone encounter this before?
--
Peter Laws | N5UWY | plaws plaws net | Travel by Train!
73,
Rich VE3KI
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty
|