You need to apply audio to pin 11 and key the radio with pin 9. Pin 13
mutes the pin 11 input.
The manual was not written by a native english speaker.
Can you confirm that you have audio on pin 11? (a scope would be good)
Do you have the mode set to SSB?
GL de W1EL
On 1/30/2014 6:40 PM, Lee wrote:
I did read the description of the pinouts on page 95.
9 P K S T r a n s c e i v e r P T T l i n e c o n t r o l
• G r o u n d t h i s t e r m i n a l t o t r a n s m i
t .
• C o n n e c t t o t h e T N C o r M C P t r a n s m i
t / r e c
e i v e s w i t c h i n g p i n f o r d i g i t a l o p e r a t i o n .
• M i c r o p h o n e a u d i o i n p u t m u t e s w h
e n t h e
t r a n s c e i v e r t r a n s m i t s .
<<----------------------------------------
11 P K D M i c r o p h o n e a u d i o i n p u t
<<-------------------------------------------------------
• C o n n e c t t o t h e T N C o r M C P t r a n s m i
t d a t a
p i n f o r d i g i t a l o p e r a t i o n .
1 3 S S P T T c o n t r o l
• G r o u n d t h i s t e r m i n a l t o t r a n s m i
t .
• F o r c o n n e c t i n g a f o o t s w i t c h o r o
t h e r e
x t e r n a l c o n t r o l l e r ( i n p a r a l l e l w i t h M I C j a c k
) .
• M i c r o p h o n e a u d i o i n p u t d o e s N O T
m u t e w
h e n t h e t r a n s c e i v e r t r a n s m i t s .
<<--------------------------------------------
As the manual reads, I need to use pin 11 for the AFSK input with pin 13 for
keying. Sure looks that way to me. But, I did try pin 9 again and and still no
modulation even though the radio is keyed.
Joe Subich, W4TV <lists@subich.com> wrote ..
Anyway, I was using pin 9 with FSK and N1MM and that was working. For
AFSK, it is my understanding that pin 9 will mute the microphone
input on pin 11.
That is incorrect. Pin 9 PTT mutes the *microphone input* - the mic
jack on the front of the transceiver (Mic jack). Pin 11 is PKD -
you connect AFSK (or TNC, MCP, etc.) audio there - Pin 9 (PKS) selects
PKD which disables compression and clipping. *READ THE MANUAL* - see
the description of ACC2 on Page 95.
If Pin 11/Pin 9 work in N1MM Logger and do not work in fldigi, you have
a configuration issue with fldigi and should seek help from those who
know fldigi. Make sure fldigi is actually triggering the PTT line on
pin 9 and not trying to switch the rig using CAT commands since they
likely to be *wrong* (equivalent to pin 13).
73,
... Joe, W4TV
On 1/29/2014 8:15 PM, Lee wrote:
Actually, this wouldn't be specific to fldigi since it's a general issue for
AFSK.
Anyway, I was using pin 9 with FSK and N1MM and that was working. For
AFSK, it
is my understanding that pin 9 will mute the microphone input on pin 11.
According to the TS2000 manual, I need to key the radio with pin 13 so
that
pin 11 isn't muted on key down.
I've tried both pin 9 and pin 13 with the same result (no AFSK
transmitted).
Joe Subich, W4TV <lists@subich.com> wrote ..
This should really be asked on the fldigi support forum ...
TS-2000 requires PTT on pin 9 (PKS) when applying audio on pin 11 (PKD).
See the description of those pins on page 94 of the TS-2000 Instruction
Manual.
73,
... Joe, W4TV
On 1/28/2014 9:57 PM, Lee wrote:
I believe that I have my PC-to-radio interface cable set up right but I
can't
seem to transmit any audio. The radio is keyed but no transmit audio. I
have
audio to ACC2-11 and my keying is on ACC2-13. I don't see any radio menu
options that would cause an issue. Also, with the microphone attached, I
can
transmit voice when the PC keys the radio so the microphone audio from
ACC2
shouldn't be muted. Receive is working properly though. What am I
missing?
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty
--
Eric Lowell
48 Loon Road
Wesley, ME 04686
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty
|