TenTec
[Top] [All Lists]

RE: [TenTec] Houston......Orion has Landed

To: <tentec@contesting.com>
Subject: RE: [TenTec] Houston......Orion has Landed
From: "John L Merrill" <jmerrill1@adelphia.net>
Reply-to: tentec@contesting.com
Date: Sun, 6 Jun 2004 10:22:38 -0400
List-post: <mailto:tentec@contesting.com>
John:
Congrats on the new Orion. What do you mean by s meter adjustment? With the
radio on and no signal or antenna attached the s meter rests at S1 if that
is your concern. That is normal. I'm also not impressed with the monitor
quality.

73,
John N1JM

-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]On Behalf Of N0KHQ@aol.com
Sent: Sunday, June 06, 2004 10:15 AM
To: tentec@contesting.com
Subject: [TenTec] Houston......Orion has Landed


Hello All,

Pulling into the driveway Thursday evening........there it sat on the front
porch......a large white box from TT.

Getting myself and the large white box through the front door was a little
bit of a challenge, but with a little grunting and twisting we finally made
it..........my only thought was to get the new rig downstairs to the ham
shack and
unpacked before the wife got home.

My first impression was:

Man, this things heavy......I think the packing material weighs as much as
the rig.

My next impression, after carefully unpacking, was:

Man, this things big.....where am I going to put it? It was obvious that the
Orion was not going to fit in the space previously occupied by the 756Proll
and Power Supply. But with a little ham ingenuity, I was able to gently
place
the Orion on the shelf above the TT Jupiter. Whew!

I had also ordered the "Orion Operations for Dummies" DVD, starring Scott
(Hollywood) Robbins, produced by TT and directed by Ed W4ZSB, but somehow
watching the DVD didn't seem real important to me right now.

Quickly hooking up the grounding, power and coax, I fired the beast up. (I
reset the CPU just out of habit)
The rig sprang to life, the blinding light from the display seemed to fill
the room. I noticed that the firmware was ver. 1.369, so my first task was
to
update to ver. 1.37. No issues were encountered during or after the
update.........cool!

Since my operations are about 80% listening and 20% transmitting, I wasn't
real concerned about the transmitter section of the Orion.

Today is Sunday, I've made, probably 6 or 7 contacts with the rig, most of
my
time has been dedicated to the operation of the receiver controls.

Man it sure is nice to use a rig that is user definable.

The Orion variable "NR" operates just as well as my "Hear it" DSP module, so
that's out of line now and sitting on the bench......don't need it any more.

I finally took the time to watch the TT DVD. By the way, if you are an Orion
owner, you may want to purchase the DVD.

The Roofing Filters in the first IF is a great idea.

The Programmable AGC works great.

The Band Scope is "near" real time. Good enough for me. To have a Band Scope
that is "Real Time" signal analysis is heavily dependent on three factors,
Programming, CPU Speed and Bus Speed. Unless you have one heck of a CPU,
"real
time" is difficult to achieve. I run a spectral analyzer on my PC (800mhz
CPU
and 100mhz bus) and its still not "Real Time" so, we can only get "close".
And
close is good enough.

The only thing that sticks out is 1. The "S" meter needs adjustment and 2.
The "Monitor" volume needs to be cranked up.

I guess the above comments and observations are enough for right now, time
to
play.


73
John / N0KHQ / St. Louis

Always on 18.130

Antennas:

You can build 'em better than you can buy 'em
Please visit the sites below:
http://www.hamuniverse.com/17mcoaxmox.html
http://www.cebik.com/n0khq.html
http://www.ssb-audio.com/forum/
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>