TenTec
[Top] [All Lists]

Re: [TenTec] Sub-receiver noise redux

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Sub-receiver noise redux
From: John L Merrill <jmerrill1@adelphia.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 20 May 2005 06:49:30 -0400
List-post: <mailto:tentec@contesting.com>
I hear the pops, which is probably the PLL relocking ( common on other 
radios). But hear no change in noise level.

John N1JM

TJ Sheffield wrote:
> I’m running firmware version 1.372 and using DX4WIN Ver. 6.04 to 
> communicate with the Orion on a serial port.
> 
> A master re-set doesn’t eliminate this condition.  Below certain 
> frequencies the noise disappears.  Cycling the power when the 
> sub-receiver is tuned below these frequencies fixes the condition, at 
> least until it recurs on a random basis.  I am unable to determine if 
> some combination of band / frequency / mode choice precipitates this 
> condition.
> 
> Rolling the sub-receiver across the following frequencies shows where 
> the noise is present or absent (by mode):
> 
> UCW  13.000.640  Present,   13.000.630 Gone
> 
> LCW  12.999.300  Present,   12.999.290 Gone
> 
> USB  12.999.970  Present,    12.999.960 Gone
> 
> LSB  12.999.970  Present,    12.999.960 Gone
> 
> AM   12.999.970  Present,    12.999.960 Gone
> 
> FM   12.999.970  Present,    12.999.960 Gone
> 
> Please try rolling your sub-receiver across these frequencies and let me 
> know if you detect an audible pop or other indication that something may 
> be happening in this region.
> 
> In my case, even when the S-5 noise is gone, I can detect an audible pop 
> when the sub-receiver is tuned across these frequencies.
> 
> Thanks very much,
> 
> TJ Sheffield, KL7TS
> Anchorage, Alaska
> 
> 
> =============================================================
> PREVIOUS POST
> 
> On an intermittent basis my Orion sub-receiver will display 
> approximately five bars of noise while the main receiver may show S-2.  
> Both receivers are on 20m at present.
> 
> If I tune the sub-receiver down to 13.000.000 the five bars of noise is 
> still displayed and the hash is still heard in the sub-receiver.  If I 
> tune to 12.999.900 the five bars of hash drops entirely and a more 
> reasonable 1-1/2 bars of normal background hiss is heard.
> 
> The sub-receiver noise at 13.000.000 and above sounds something like a 
> mixture of high and low tones that are cycling, burbling and/or pulsing 
> at a rapid rate.  Sorry I don’t have a more technical description for 
> this noise!  Tuning to 12.999.900 and below the hash disappears and I 
> hear the normal background hiss of a quiet band.
> 
> If the sub-receiver is above 13.000.000 and I cycle the main power 
> switch off / on the condition persists.  If I tune to 12.999.990 and 
> cycle the power the condition is cured but a noticeable pop is heard 
> when rolling from 12.999.900 to 13.000.00 however the sub-receiver hash 
> is gone.
> 
> When the sub-receiver noise is present the rig is not useable for split 
> operation but the cure at least is available.  I’m running the latest 
> firmware.
> 
> These observations will be cross-posted to “ditsnbits” but I though I’d 
> mention it to the group.
> 
> Thanks very much,
> 
> TJ Sheffield, KL7TS
> Anchorage, Alaska
> 
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>