Sounds like your output pot is making poor contact, at times, like a scratchy
volume control. A shot of tuner cleaner into the pot, while not operating,
might just cure it. Obtainable from the local electronics store in the mall.
Bruce
Denton <denton@oregontrail.net> wrote: Check the dc power plug...and the dc B+
path...fuse, wiring, etc..to the
finals.
----- Original Message -----
From: "Peter Hoon"
To: "Discussion of Ten-Tec Equipment"
Sent: Sunday, March 11, 2007 5:55 PM
Subject: [TenTec] Omni VI+ Intermittent Power Amp?
> Fellows,
>
> Have you got suggestions for the case of intermittent power out from an
> Omni
> VI Plus?
>
> First year (May 2006 - March 2007) since I am the second owner, no
> intermittent noticed; always got full 100 watts on all bands (10 M a
> little
> low, around 90 W out).
>
> Now in second year of ownership. Very clean unit; complete and successful
> receiver alignment matches ARRL MDS.
>
> Suddenly, while operating on 40M CW, into perfectly 1:1 tuned loop via
> Dentron tuner, can only get 7 to 9 watts out max on all bands.
>
> Next day, try again, and get full power again on all bands for next 5
> days.
> Completely normal operation.
>
> Hook to 300 W dummy load on bench.
>
> Adjust bias pots to confirm linear class AB output on SSB; Speech sounds
> fine on adjacent receiver after adjustment; normal full power out after
> bias
> pot adjustments.
>
> All of a sudden, with no changes anywhere, can only get 7 to 9 watts out
> again for next 24 hours.
>
> Thinking it might be thermal, wait overnight for cold transceiver. In
> morning, cold, only 7 to 9 watts out. Two tries, same low power result.
>
> Remove power amp module from rear. Remove blue T wire and coax input from
> jack 79. Careful inspection of top circuit board, shows no loose screws,
> finals are clean, no obvious cold solder joints; replace blue wire and
> coax
> input.
>
> I have MRF 454 finals. Throughout testing, heat sink is hardly even warm
> to
> touch. Power meter on Dentron tuner and on Omni VI Plus match each other;
> not a measurement problem.
>
> Turn power out-put pot, front panel, from min to max, and only 7 to 9
> watts
> out.
>
> Turn power output pot back to min again, move up to max, and bingo,
> completely normal 100 watts out on all bands!
>
> There were no changes. What the heck is going on!
>
> Would like to know if anyone elase has experienced this kind of transmit
> intermittent with an Omni VI plus. What did you find was the cause?
>
> Am about to go back up and wiggle some more components and wires.
>
> May also remove power amp circuit board and check the underside for cold
> solder joints.
>
> Thanks for suggestions and ideas; will report findings for posterity.
>
> Peter
> VE1CHS
> Nederland, Colorado
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
---------------------------------
Never miss an email again!
Yahoo! Toolbar alerts you the instant new Mail arrives. Check it out.
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|