TenTec
[Top] [All Lists]

[TenTec] parts not SS

To: Ten Tec List <tentec@contesting.com>
Subject: [TenTec] parts not SS
From: Charles Harpole <k4vud@hotmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 1 May 2009 07:39:09 +0000
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Yep, many brands of hose clamps have a plated

screw which fails before the SS part, of course.

Weird construction.  I goop such clamp screws

with black sillycone sealer all around... do not leave

voids which will fill with water.

The raw fiberglass rods that insulate parts on some

Cushcraft will start to "hair off" without the same

sillycone treatment.  Electrical tape, so often the

ham's "friend" is just not ....  it shrinks and curls,

withdraws the end leaving a flag, or cracks.

Seal coax fittings with one wrap of electrical tape, NOT

pulled so tight, followed by a wrap of CoaxSeal, followed

by a loose wrap of electrical tape.  The inner tape allows fast

and clean removal of the CoaxSeal, the CoaxSeal keeps the

water out, and the outer wrap protects the CoaxSeal from

being scraped off by accidental movement of the cable.

Do not use sillycone sealer directly on coax plugs because

the evaporation of the stuff often evaporates INSIDE itself,

making a nice acidic splash on ur plug.  73,
 

Charles Harpole
k4vud@hotmail.com   







> From: Dave@k6wrf.com
> To: tentec@contesting.com
> Date: Thu, 30 Apr 2009 22:35:41 -0700
> Subject: Re: [TenTec] OT: cleaners, etc
> 
> I've noticed that the clamp is SS all except the screw.
> My 2 cents.
>                        Dave K6WRF
> 
> 
> ----- Original Message ----- 
> From: "CSM(r) Gary Huber" <glhuber@msn.com>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Thursday, April 30, 2009 5:20 PM
> Subject: Re: [TenTec] OT: cleaners, etc
> 
> 
> > Lowes has been my source of SS hose clamps recently when I've had to 
> > repair
> > ice storm damage on my Butternut HV-2.... also Deer damage and John Deere
> > lawn tractor damage.
> >
> > --------------------------------------------------
> > From: "Jack B. Friend" <jfriend31@comcast.net>
> > Sent: Thursday, April 30, 2009 4:05 PM
> > To: <geraldj@storm.weather.net>; "Discussion of Ten-Tec Equipment"
> > <tentec@contesting.com>
> > Subject: Re: [TenTec] OT: cleaners, etc
> >
> >> one can find real and complete stainless steel hose clamps at auto parts
> >> houses, sometimes at Home Depot and Lowe's too.
> >>
> >> jack
> >>
> >> On Thu, 2009-04-30 at 00:35 -0600, Dr. Gerald N. Johnson wrote:
> >>> On Thu, 2009-04-30 at 10:47 -0500, CSM(r) Gary Huber wrote:
> >>> > Stainless steel hose clamps for compression of joints and splices.
> >>> >
> >>> > 73 es DX,
> >>> >
> >>> > Gary - AB9M
> >>> >
> >>> But not the ones with plated steel parts. They rust too much. 100%
> >>> stainless steel hose clamps do exist. McMaster-Carr and Heartland Agri-
> >>> Supply are two sources that I know of.
> >>>
> >>> Gerald J.
> >>>
> >>> _______________________________________________
> >>> TenTec mailing list
> >>> TenTec@contesting.com
> >>> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>