TenTec
[Top] [All Lists]

Re: [TenTec] Popping in O1 audio during AF adjust

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Popping in O1 audio during AF adjust
From: Reed Krenn <reed.krenn@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 14 Jul 2010 22:07:08 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I am going to be *so* embarrassed if that's all it is......

BUT, I do have them looking at another trouble.

-- Reed / WW3A

On Wed, Jul 14, 2010 at 7:29 PM, art davis <n4uc@hotmail.com> wrote:

>
>
>
>
>
>
> Here is the response I got from the TenTec service manager within 3 hours
> of me posting this. Now that's service!
>
> First do RAM clear reset followed by a master reset and
> clear user memories
>
> and filter settings should be performed. RAM clear is as follows:
>
> 1. Orion off, power supply on.
>
> 2. Press and hold the LCK button just below the VFO B knob.
>
> 3.Turn on Orion and continue to hold the LCK button until Master Reset
> is
>
> displayed on the screen. BATTERY FAILURE may also be displayed,
> disregard.
>
> 4. Release the LCK button and allow the Orion to boot to 14.250.
>
> 5. Turn the Orion Off and perform the Master Reset using The MAIN RX/TX
>
> button. User memories and filter settings MUST be cleared.
>
> It took care of it for me...gud luck
>
> > Date: Wed, 14 Jul 2010 18:50:12 -0400
> > From: reed.krenn@gmail.com
> > To: tentec@contesting.com
> > Subject: Re: [TenTec] Popping in O1 audio during AF adjust
> >
> > I misspoke; mine also occurs with rotation of either of the VFO encoders.
> >
> > -- Reed / WW3A
> >
> > On Wed, Jul 14, 2010 at 6:45 PM, Reed Krenn <reed.krenn@gmail.com>
> wrote:
> >
> > > I just shipped my (Classic) Orion to Ten Tec *today* for the exact same
> > > problem.
> > >
> > > I'll report the results to the reflector.
> > >
> > > Reed / WW3A
> > >
> > >
> > > On Tue, Jul 13, 2010 at 11:30 PM, art davis <n4uc@hotmail.com> wrote:
> > >
> > >>
> > >> My O1 (2.0.6.2a) has recently developed a popping in the left audio
> > >> channel of the headphone output when adjusting the volume of either
> the MAIN
> > >> or SUB AF. The rate of the popping seems to be in sync with the
> rotation of
> > >> the AF controls (optical encoder?) and its volume goes up and down
> with the
> > >> audio volume. In the headphones it sounds just like you ears popping
> during
> > >> flying or diving under water. The popping is not affected by the mode,
> RF
> > >> gain, sidetone volume, MON setting, or any other front panel control
> > >> setting, except as described for the AF controls.
> > >> Any ideas?
> > >>
> > >>
> > >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _________________________________________________________________
> The New Busy is not the too busy. Combine all your e-mail accounts with
> Hotmail.
>
> http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>