TenTec
[Top] [All Lists]

Re: [TenTec] Suggestions please

To: tentec@contesting.com
Subject: Re: [TenTec] Suggestions please
From: "Dr. Gerald N. Johnson" <geraldj@weather.net>
Reply-to: geraldj@weather.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 09 Jan 2011 12:39:45 -0600
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I had more trouble with wind with TV twinlead over the past 39 years in 
central Iowa. Ice was harder on the 18 gauge copperweld open line. The 
wire simply snapped when a breeze flexed the feed line while encased in 
ice. Twisting the twinlead may have been a benefit to break up the 
airfoil lifts that made it flop in the wind.

73, Jerry, K0CQ

On 1/9/2011 12:34 PM, Rsoifer@aol.com wrote:
> Jerry,
>
> Iowa may be a worse environment for ice than New Jersey where I was at the
> time, but I had no problems with mechanical strength.  Of course, my
> feedline run was only 50 feet, pretty much straight up.
>
> 73 Ray W2RS
>
>
> In a message dated 1/9/2011 5:48:47 P.M. GMT Standard Time,
> geraldj@weather.net writes:
>
> But the  TV grade line needs help in the support department. 22 gauge
> copper wires  aren't strong enough to take the wind and ice load on the
> flat of the  insulation. I figure on punching holes every 6 or 8 inches
> and feeding an  insulating rope through them, probably take a turn around
> one or both  sides between passes through the holes to give more support
> and to break  up the airfoil. I might use parachute cord for that support
> rope. Then tie  the upper end to the center insulator and the lower end
> to some sort of  anchor before going to the feedthrough to get into the
> shack.
>
> 73,  Jerry, K0CQ
>
> On 1/9/2011 11:36 AM, Rsoifer@aol.com wrote:
>>   Tom,
>>
>> In a pinch, I have used Radio Shack's "heavy duty"  300-ohm twin-lead with
>> power levels up to 500 watts.  No  problems.
>>
>> 73 Ray W2RS
>>
>>
>> In a message  dated 1/9/2011 5:07:40 P.M. GMT Standard Time,
>> xring97015@gmail.com  writes:
>>
>> I have  been off the air for a while and am now  trying to get back up to
>> speed(cw  only here). I need to rebuild  my antenna and am curious what
> you
>> folks  recommend for a ladder  fed doublet- buy or build. Also I want to
>> reassess  my  tuner/balun set up. I know this is a gigantic can of worms
> and
>> has  been  hashed since the beginning.
>>
>> I use an OMNI VI and  only run 100 watts. I  do not have plans to install
> a
>> power  amplifier at this location. I am  looking for efficiency and need
> to
>> avoid causing interference as my home is  close to the  neighbors.
>> Thanks in advance for any suggestions.
>>
>>   Tom  Stewart N7ESE
>>   _______________________________________________
>> TenTec   mailing  list
>> TenTec@contesting.com
>>   http://lists.contesting.com/mailman/listinfo/tentec
>>
>>   _______________________________________________
>> TenTec mailing  list
>> TenTec@contesting.com
>>   http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec  mailing  list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>