TenTec
[Top] [All Lists]

Re: [TenTec] Jupiter CW personality problem

To: Mark Milburn <markkq0i@yahoo.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Jupiter CW personality problem
From: Tim Cook <nz8j@woh.rr.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 31 Aug 2011 06:13:17 -0400
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Thanks Mark , you hit it on the head, I just put the latest "normal".  
Jupiter firmware on it and it is fine now. I am a cw op but have no  
need for a cw reader.

It's an amazing little radio for what it is.

73
Tim
NZ8J

Sent from my iPhone

On Aug 30, 2011, at 9:14 PM, Mark Milburn <markkq0i@yahoo.com> wrote:

> Don't think I went far enough in explaining...if you won't be
> using the CW mode, you don't HAVE to install the larger
> chip.  Just download the 538 mode from the Ten Tec site and
> load it into the Jupiter.  It will replace the CW mode and you
>
> will be able to use the Jupiter just as it was originally issued,
> it just won't have the reader and probably some other stuff
> that was added when they wrote the CW personality.
>
>
> Mark Milburn    KQ0I
> Des Moines, IA
>
>
> on Skype as:  markkq0i
>
>
>> ________________________________
>> From: NZ8J <nz8j@woh.rr.com>
>> To: tentec@contesting.com
>> Sent: Tuesday, August 30, 2011 6:05 PM
>> Subject: [TenTec] Jupiter CW personality problem
>>
>> Hi,
>> I just bought a used Jupiter, (older model with green screen and gray
>> case). It looks and works fine with one problem. The guy who I  
>> bought it
>> from briefly mentioned it had the CW personality Firmware. It's there
>> but doesn't work like the instructions on the Ten Tec web page says.
>>
>> My question is, were there different levels of upgrade from the  
>> regular
>> Jupiter to the newer CW personality?  I don't know much about it  
>> and the
>> person I bought it from has not been of any help. The cw reader  
>> seems to
>> work, I can tune a cw signal and it will decode the signal if it is
>> strong enough but I can't get the radio to go back to the regular 538
>> mode.
>>
>> While in the CW mode, you don't have AM or FM capabilities and I  
>> like to
>> listen to AM BCB/SW. I operate cw 99% of the time but have no need  
>> for
>> the decode function.
>>
>> Holding the "MODE" switch in doesn't give me the option to pick GO  
>> 538
>> or CW
>>
>> When turning on the radio the screen indicates :
>>
>> JUPITER 538 CW
>>
>> REV 1.03  b4  11.18.2008
>>
>> Any help or suggestions would be greatly appreciated. I'm reluctant  
>> to
>> reload any new firmware until I have a better idea of what is going.
>>
>> I would like to just go back to the latest regular Jupiter firmware  
>> if
>> possible. I've looked through the archives but don't really see  
>> anything
>> that describes my situation.
>>
>> If anyone is familiar with the Jupiter and the upgrade to the cw
>> personality and has an idea of what I am trying to describe I would
>> appreciate corresponding off the list
>>
>> My email is nz8j@woh.rr.com
>>
>> Thanks
>> Tim
>> Nz8J
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>