TenTec
[Top] [All Lists]

Re: [TenTec] Slightly OT

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Slightly OT
From: "Art Trampler" <atrampler@att.net>
Reply-to: atrampler@att.net, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 18 Sep 2011 13:56:22 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Rick,

I'll try adding it. The reason I didn't think that way is that the internal
tuner handles things fine, and the 238 has a wider tuning range. As you
said, though, it may be quirky under some conditions.

The ladder line goes to a 4:1 current balun (in the crawl space) from Balun
Designs. From there it passes through a TT350 arrestor, and then to the
tuner via 10' of LMR600. I went with the 600 to minimize losses due to SWR
mismatch, and I think that 10' is short enough that the losses should not be
a problem. Of course with a little bit extra coax from the tuner to
wattmeter, wattmeter to amp, I then have 12' or so...close enough to 1/4
wave on 15 and 17 (and maybe 12 and 10) to be worrysome.

Art

-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Rick - DJ0IP / NJ0IP
Sent: Sunday, September 18, 2011 9:46 AM
To: atrampler@att.net; 'Discussion of Ten-Tec Equipment'
Subject: Re: [TenTec] Slightly OT

Art,

Once the open wire reaches the shack, how do you connect to the 238B?
Directly using its built-in balun?

The first thing I would do it use an external balun, a good 4:1 current
balun if you have one, and then try it.

The next thing I would do is add 11 ft. more open wire to the feedline.
This is about 1/8 wavelength on 15m.

Although the 238B (or C, etc.) is my favorite matchbox on the planet, its
weakness (IMHO) is when the Inductor needs to be at minimum for best match.

I have has multiple cases (all on 40m if I recall right), where I had the L
set to minimum, but middle in the band I would have to switch between "Hi"
and "Lo" to get minimum SWR.  It just seemed flaky.
In these cases I used one of my other tuners; typically my MFJ-986.
On other bands, sparks would fly inside the 986 and the 238 would match it
like a champ.

For that reason I keep two matchboxes.  (For high power)

Unfortunately I cannot tell you exactly what is going on.  But I'm confident
changing the feedline length will fix it.

73
Rick



-----Original Message-----
From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
On Behalf Of Art Trampler
Sent: Sunday, September 18, 2011 3:32 PM
To: 'Discussion of Ten-Tec Equipment'
Subject: [TenTec] Slightly OT

Hi Gang,

 

This is an antenna/impedance transformation device question, but the devices
in question are a Ten-Tec 238B, and the (LDG) internal tuner on a Pegasus.

 

Antenna: 140? sloping dipole, apex at 45 feet in a tree, ends around 28?. It
is fed with 10? of LMR600 to a 4:1 current balun, and from that point with
about 100? of near-600 ohm ladder line (4? spreaders from www.cnc73.com).

 

Symptoms: The internal tuner finds a match on all bands other than 160
(where the whole antenna is ¼ wavelength). With the 238B I cannot match 17,
15, 12 or 10. The best I might see if 4:1, and even then it is very
sensitive, such that any adjustments vary the displayed output in an Autek
WM-1 wattmeter as well as the calculated SWR. Measured output on the Autek
might fall to ?0.? I tend to rely on the reverse power setting on the 238B
for tuning, but as SWR falls, so often does the measured output. 

 

The closest match on these bands is found in ?bypass? on the 238B.

 

All this was done with 10 to 25 watts output.

 

Knowing that the 238B has a wider tuning range than the internal LDG tuner,
I am a bit perplexed. Could it be poor grounding? Beefing the grounding of
the antenna tuner is one of my next projects. Or could it be stray
inductance within the tuner that I cannot get rid of merely by setting the
inductor all the way counter-clockwise? That is what I tend to believe.

 

Your thoughts? 

 

In other news, all relays replaced on Pegasus and it works fine, and grid
protection circuit for 425 nearly ready to test and drop in.

 

73,

Art K0RO

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>