TenTec
[Top] [All Lists]

Re: [TenTec] Omni VI + Interconnect Schematic

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Omni VI + Interconnect Schematic
From: Clayton Brantley <clayton_n4ev@yahoo.com>
Reply-to: Clayton Brantley <clayton_n4ev@yahoo.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 10 Dec 2011 13:27:09 -0800 (PST)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Hello Barry:  Yes, I'll include you in the feed too.  I'll try to get that this 
PM

73 Clayton N4EV



________________________________
 From: Barry N1EU <barry.n1eu@gmail.com>
To: Clayton Brantley <clayton_n4ev@yahoo.com>; Discussion of Ten-Tec Equipment 
<tentec@contesting.com> 
Sent: Saturday, December 10, 2011 3:09 PM
Subject: Re: [TenTec] Omni VI + Interconnect Schematic
 
You're right, great catch!  It's an unnumbered page after 4-62 and
only in the 563 manual.

Clayton, can you please send it to me as well?  I will add it to the
Ten-Tec Wiki.

Thanks & 73,
Barry N1EU

On Sat, Dec 10, 2011 at 7:37 PM, Clayton Brantley
<clayton_n4ev@yahoo.com> wrote:
> Wayne:  There is an interconnect drawing in my 563 manual.  I'll try to copy 
> and attach to an email.
>
> Clayton N4EV
>
>
> ________________________________
>  From: Barry N1EU <barry.n1eu@gmail.com>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Sent: Saturday, December 10, 2011 12:55 PM
> Subject: Re: [TenTec] Omni VI + Interconnect Schematic
>
> There is no interconnect drawing in either the 563 or 564 manuals.
>
> 73, Barry N1EU
>
> On Sat, Dec 10, 2011 at 5:46 PM, Clayton Brantley
> <clayton_n4ev@yahoo.com> wrote:
>> Wayne:  I have an Omni VI rev 3 and I'm sure there is a drawing the the 563 
>> manual.  I'll look a bit later
>> today for you.
>>
>> I did a quick check on the 564 book that I downloaded and you're right!  
>> It's missing!
>>
>> 73 Clayton N4EV
>>
>>
>>
>> ________________________________
>>  From: n2wk <n2wk@rochester.rr.com>
>> To: tentec@contesting.com
>> Sent: Saturday, December 10, 2011 12:03 PM
>> Subject: [TenTec] Omni VI + Interconnect Schematic
>>
>> Is there a drawing (schematic)for the Omni VI+ showing all of the 
>> interconnect boards available?
>> I do not have one in my Omni VI Plus manual. This would be a large Drawing 
>> showing the entire layout of the connections from board to board. I could 
>> use one. Anybody Please.
>>
>> 73, Wayne N2WK
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>