TenTec
[Top] [All Lists]

Re: [TenTec] 318 and 717

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] 318 and 717
From: Barry N1EU <barry.n1eu@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 1 Feb 2012 20:59:50 +0000
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I think you can just do a RAM Clear operation and you'll be presented
with the question again.  If for any reason that didn't work, you can
always just reload the firmware.

Barry N1EU

On Wed, Feb 1, 2012 at 8:40 PM, TroyW6HV <w6hv@verizon.net> wrote:
> I've ordered the RX366 (I expect it sometime next week), if I install the
> firmware now and answer "NO" to the receiver installed question. Would I
> then need to re-install the firmware after installing the RX366?
> Thanks,
> Troy, W6HV
>
> -----Original Message-----
> From: Barry N1EU
> Sent: Wednesday, February 01, 2012 11:29 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] 318 and 717
>
> after you load the v3 firmware, a question will pop up on the Orion
> screen asking if the RX366 is installed - you just say "no" (or "yes")
> and off you go
>
> Barry N1EU
>
> On Wed, Feb 1, 2012 at 7:28 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>> absolutely - new subreceiver support was only a minor part of the new
>> firmware
>>
>> Barry N1EU
>>
>> On Wed, Feb 1, 2012 at 7:26 PM, John Sheeley <wb4qda@yahoo.com> wrote:
>>> John
>>>
>>> Can we use  verison 3 firmware  on our Orion II with out installng tne
>>> new 2nd receiver ?
>>>
>>> 73 John wb4qda
>>>
>>>
>>> ________________________________
>>>  From: John Henry <jhenry@tentec.com>
>>> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
>>> Sent: Wednesday, February 1, 2012 10:39 AM
>>> Subject: [TenTec] 318 and 717
>>>
>>> I've had several emails requesting more info on the 318 and 717.
>>> They are on the website, and can be found by
>>> go to: www.tentec.com
>>> Type in the model number into the search box on the left side of the
>>> window.
>>> Hit enter
>>> The link to that product will pop right up.
>>> Click on the pic of that product, and then a lot of info is there.
>>> Of course, if you need more info, then feel free to contact myself
>>> or service at tentec.com.
>>> Paul Clinton can answer questions quicker than I can.
>>>
>>> Already sold a bunch of 366s,
>>>
>>> John
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>