TenTec
[Top] [All Lists]

Re: [TenTec] RX-366?

To: tentec@contesting.com
Subject: Re: [TenTec] RX-366?
From: Ron Notarius W3WN <wn3vaw@verizon.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 24 Apr 2014 10:17:32 -0500 (CDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I really doubt there's anything sinister going on here, gang.
 
I suspect one of two things as being the core issue:
 
First:  
 
Consider that the Orion's are no longer in production.  So the remaining market 
for the RX-366 may be very small.
 
In that case, I'd venture that Ten-Tec has merely sold out of the existing 
stock, and that the decision makers feel that there isn't enough of a remaining 
potential market to warrant another production run.
 
Second:  
 
There may be some technical changes being made to the Eagle receiver board(s) 
for the next production run of the Eagle.  (Improved performance-related, or 
swappingno-longer-available part(s) for others, that sort of thing).  Since the 
RX-366 is based on the Eagle receiver, these possible updates may mean that the 
RX-366 also needs similar updates.  So, there may be a replacement coming 
out... or, again, if there's no longer believed to be enough of a market to 
warrant continued production of an updated board...
 
I'm sure we'll find out what's going on in due course.
 
73, ron w3wn

On 04/24/14, Eric Zust - W0TT wrote:

Gents,

I bought an RX-366 on 11 Feb 2014 along with a Ten-Tec model 2001, 600 Hz
CW filter. I was not aware of the InRad filters when I ordered the parts
from Ten-Rec.

I received and installed the board and filter in my Orion II, and it is
working with just a few issues. I've discussed the issues and installation
with Ten-Tec service, and they are advising me to uninstall & reinstall the
boards (to make sure all contacts are seated properly), or to return the
Orion to them. I haven't done it yet, but I will try the
uninstall/reinstall option first, so that I don't have to take the rig out
of service.

And I did not notice until reading this thread, that Ten-Tec has removed
almost all mention of the RX-366 from their website. I had their sales page
bookmarked, and it now results in "page not found". So I would speculate
that they have likely sold-out of their stock.

Ten-Tec still has the RX-366 installation instructions posted on their
web at:

https://www.tentec.com/content/downloads/manuals/RX366/74467%20Rx366%20V1.4%
202-16-12%20Instructions.pdf

Eric - W0TT



-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Kim Elmore
Sent: Wednesday, April 23, 2014 9:51 PM
To: Discussion of Ten-Tec Equipment
Subject: [TenTec] RX-366?

I'm considering getting RX-366 with a full set of filters. Which are the
better roofing filters: the InRad or the TT filters? 

Also, I couldn't find any mention of the RX366 on the TT site. Did I miss a
memo?

Kim N5OP

"People that make music together cannot be enemies, at least as long as the
music lasts." -- Paul Hindemith
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>