TenTec
[Top] [All Lists]

Re: [TenTec] Ten Tec Phone number? A9 caps.

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Ten Tec Phone number? A9 caps.
From: Barry N1EU <barry.n1eu@gmail.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 19 Jan 2016 10:24:04 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Ten-Tec really has their hands full with starting up.  I doubt they know
more than what all is expressed on the wiki page at
http://www.tentecwiki.org/doku.php?id=565pwrdistfail

Barry N1EU

On Tue, Jan 19, 2016 at 10:15 AM, Froiseth Richard <Rfwd6dok@centurylink.net
> wrote:

> Thank you I will give it a try.
>
> 73’s
> Rich, WD6DOK
>
>
>
>
>
>
>
> > On Jan 19, 2016, at 8:11 AM, Jim Vohland <n9vo@hotmail.com> wrote:
> >
> > Did you try email to the: service@tentec.com address listed on webpage.
> It says they are monitoring that email. Should get ya a response.
> >
> >
> >> From: Rfwd6dok@centurylink.net
> >> Date: Tue, 19 Jan 2016 07:36:03 -0700
> >> To: tentec@contesting.com
> >> Subject: [TenTec] Ten Tec Phone number? A9 caps.
> >>
> >> Is there a phone number that I can contact Ten Tec on... or are they
> not taking calls?
> >> I ordered the caps for the A9 board and they did not send one.  Maybe
> this cap does not need replacing.  100uf 6.3v loc c8-3.
> >> I assume all of the caps should be replaced… true.
> >> Any help would be appreciated… or should I order one from Digi-Key or
> elsewhere.
> >>
> >>
> >> 73’s
> >> Rich, WD6DOK
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>> On Jan 18, 2016, at 4:44 PM, Carl Winkles <jcwinks@att.net> wrote:
> >>>
> >>> You might check the power connector on the rear of the Herc II. I have
> had bizarre things happen when fewer than all of those pins are making
> contact.
> >>>
> >>> Carl, K4SEV
> >>>
> >>> Enviado desde mi iPhone
> >>>
> >>>> El ene 18, 2016, a las 5:29 PM, Zivney, Terry <00tlzivney@bsu.edu>
> escribió:
> >>>>
> >>>>
> >>>> My Hercules II  was working but now..
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> On power up (with matching TenTec power supply) the front
> >>>>
> >>>> panel fault light comes on as does the fan.  Waiting a few
> >>>>
> >>>> seconds, the red led fault light dims out and the fan stops,
> >>>>
> >>>> but the meter lights still have full brightness.  The amp
> >>>>
> >>>> does not switch over to XMT (a good thing, without the blower!)
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> Any ideas what to check first?
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> Terry N4TZ
> >>>> _______________________________________________
> >>>> TenTec mailing list
> >>>> TenTec@contesting.com
> >>>> http://lists.contesting.com/mailman/listinfo/tentec
> >>> _______________________________________________
> >>> TenTec mailing list
> >>> TenTec@contesting.com
> >>> http://lists.contesting.com/mailman/listinfo/tentec
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>