I meant to ask if the Signal Link is a necessity with Winmor.
I'm using the serial cable for rig control and that set up keys the rig fine
when I'm running MMTTY and FLDigi
Joe, K8MP
-----Original Message-----
From: Jim Carragher <k7ikn2@gmail.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Fri, Mar 2, 2018 9:00 pm
Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus
I used the Icom 735 with Signal Link with my Omni VI Plus. Jim K7IKN
On Fri, Mar 2, 2018 at 3:52 PM, Joe Papworth via TenTec <
tentec@contesting.com> wrote:
> Thanks Greg,
> I keep muffin fans blowing on the rig's heat sink and power supply's heat
> sink most of the time already.
>
> Later, Joe, K8MP
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Greg S via TenTec <tentec@contesting.com>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Cc: Greg S <oldlongbeard@yahoo.com>
> Sent: Fri, Mar 2, 2018 06:37 PM
> Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus
>
>
> The radio address is different, if it matters, and I would be sure to get
> a fan on your heatsink.
> Greg KC8HXO
> --------------------------------------------
> On Fri, 3/2/18, Joe Papworth via TenTec <<a href="mailto:tentec@
> contesting.com">tentec@contesting.com</a>> wrote:
>
> Subject: Re: [TenTec] Winlink and Winmoor on an Omni 6 Plus
> To: <a href="mailto:w7zrc@yahoo.com";>w7zrc@yahoo.com</a>, <a
> href="mailto:tentec@contesting.com";>tentec@contesting.com</a>
> Cc: <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a>
> Date: Friday, March 2, 2018, 5:38 PM
>
> Thanks Rod. I'll check it
> out.
> Later, Joe, K8MP
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Rod Greene via TenTec <<a href="mailto:tentec@contesting.com";>
> tentec@contesting.com</a>>
> To: Discussion of Ten-Tec Equipment <<a href="mailto:tentec@
> contesting.com">tentec@contesting.com</a>>
> Cc: Rod Greene <<a href="mailto:w7zrc@yahoo.com";>w7zrc@yahoo.com</a>>
> Sent: Fri, Mar 2, 2018 05:34 PM
> Subject: Re: [TenTec] Winlink and Winmoor on an
> Omni 6 Plus
>
>
> Joe, seems like I used Icom 735 (some older
> version like that) with my Paragon that has an N4PY chip.
> The Omni 6 may be the same
> GL es 73,
> Rod/w7zrc
>
>
> From: Joe Papworth via TenTec
> <<a href="<a href="mailto:tentec@contesting.com";>tentec@contesting.com
> </a?">mailto:tentec@contesting.com";>tentec@contesting.com</a</a>>>
> To: <a href="<a href="mailto:tentec@contesting.com";>tentec@
> contesting.com</a?">mailto:tentec@contesting.com";>tentec@contesting.com
> </a</a>>
>
> Cc: <a href="<a href="mailto:k8mp@aol.com";>k8mp@aol.com</a?">mailto:k8mp@
> aol.com">k8mp@aol.com</a</a>>
> Sent: Friday, March 2, 2018 2:08 PM
> Subject: [TenTec] Winlink and Winmoor on an
> Omni 6 Plus
>
> Gents,
> Winmoor does not support the Omni 6 Plus in
> their Rig Control software.
> I'm thinking
> that someone once told me there was a different brand and
> model that used a command set equal to or very similar to
> the Omni 6.
> Does that ring any bells?
>
> Or, has anyone found another
> work-around for this problem?
>
> Thanks, Joe, K8MP
>
>
>
> _______________________________________________
> TenTec mailing list
> <a
> href="<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com
> </a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
> <a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec";
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
> target="_blank"><a href="http://lists.contesting.
> com/mailman/listinfo/tentec</a" target="_blank">http://lists.
> contesting.com/mailman/listinfo/tentec</a</a>>
>
>
>
> _______________________________________________
> TenTec mailing list
> <a
> href="<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com
> </a?">mailto:TenTec@contesting.com";>TenTec@contesting.com</a</a>>
> <a href="<a href="http://lists.contesting.com/mailman/listinfo/tentec";
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>"
> target="_blank"><a href="http://lists.contesting.
> com/mailman/listinfo/tentec</a" target="_blank">http://lists.
> contesting.com/mailman/listinfo/tentec</a</a>>
> _______________________________________________
> TenTec mailing list
> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>
> _______________________________________________
> TenTec mailing list
> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|