Well, I changed the belt this morning to one 1/2" shorter. Frankly, it
still slipped until I removed the residue remaining from the Belt
Dressing on both pulleys with alcohol. The temperature was about 25F,
and I was able to fully extend the tower without any problems.
I seem to be getting the opposite effect with the Belt Dressing. Maybe
I just put too much on. I can't explain it otherwise.
73 and thanks for all your help.
Joe
paul@w8aef.com wrote:
>It could also be that the belt is too narrow and rides in the bottom of the
>pulleys. The belt dressing is a good idea. Even if it slips when first
>applied it will (should) reduce slippage in the future.
>
>There doesn't seem to be a brand name on my belt. There are two sets of
>numbers on it: 321 E 12 and 43517. I think the 43517 is the manufacturers
>part number. This is a belt that I purchased to replace the worn belt that
>came with the tower. Sorry, can't remember where I obtained it, maybe an auto
>parts store. This belt also has 'teeth', for lack of a better word. It does
>not have the same continuous cross-section, it has teeth.
>
>Also, the Tri-ex bill of materials calls for either a Dayco 4L410 or Gates
>2410 belt.
>
>de Paul, W8AEF
> ----- Original Message -----
> From: Joe Giacobello
> To: k0dan
> Cc: paul@w8aef.com ; Tower Talk ; k6ll@adelphia.net ; KJ6Y@aol.com ;
> K9RB@bellsouth.net ; wa3gin@erols.com
> Sent: Thursday, November 24, 2005 7:27 PM
> Subject: Re: [TowerTalk] Belt Slippage on LM-470 Towers
>
>
> Thanks, Paul, Dan, Skip, both Daves and Roger.
>
> To answer several questions, I had recently changed to a new belt, applied
> grease to the drum via the fitting and changed the gearbox oil. Frankly, I
> may have been a little lax about oiling the pulley bearings on one tower, but
> I know I had done it recently on the other tower. I really don't think the
> issue is the pulleys or obstructions to the movement of sections.
>
> Usually, I can get things to work properly by simply retightening the belt.
> In fact, I got it running yesterday and while it was going up sprayed Belt
> Dressing on the pulleys. The slippage immediately began again. I think that
> Belt Dressing is more of a lubricant and seems to make the problem worse.
> The can says it is for the elimination of squeaks.
>
> The idea of reducing the belt size by a half inch makes a lot of sense. In
> the past I had blindly replaced the belts with the identical size that came
> with the towers. I bought a shorter belt yesterday and will try it out on
> Friday.
>
> Frankly, I had no idea that there was some kind of clutch mechanism
> associated with the large pulley. I knew that the mounting hardware was
> unusual, but that information was a revelation. I'll pay more attention to
> it in the future.
>
> I'll let you know how the shorter belt works tomorrow.
>
> 73, Joe
>
>
>_______________________________________________
>
>See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
>Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
>questions and ask for Sherman, W2FLA.
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|