Glad to hear you now have a working antenna Bill. From your new
information, I would conclude that my speculation was correct, a power
supply problem. It is possible that there may also be a motor problem,
but this should have not created a controller shut down. The motor
could be completely shorted out (or open) and the controller should not
shut down due to the fact that it is being driven from a current source.
If excessive motor noise was caused by "unsynchronized motor activity"
then this would be a controller problem, probably caused by transients
on the power line.
It is interesting that the original power supply is now working. I
wonder how long that will last. Initial tests at the tower with a short
cable also worked, then failed some time later.
I wonder if we will hear an official diagnosis. I wonder how you
explain 12 volt, 6 amp spikes on a 33 volt power supply rated for 2 amps
on a working SteppIR.
Jerry, K4SAV
Bill Carnett wrote:
>Greetings to all Tower Talkers,
>
>I wanted to provide an update to all that offered
>lot's of very thoughtful suggestions with the problems
> I was having with my new 4 Element. Though this is a
>SteppIR specific issue, you all contributed a whole
>lot of help to the evaluation process...THANK YOU!
>
>Though a final diagnosis will probably only be
>available after autopsy of the reflector motor, which
>seems to have been the problem or a significant part
>of the problem.
>
>A heavy duty power supply was sent to me by Mike
>Mertel last week, non-switching type. Prior to
>installing it, I ran through the testing with short 10
>foot cable at the base of the tower, total cable
>length 80 feet. Initial switching up and down the
>bands went ok, then the controller shut down.
>Attempts were made at calibration, but the unit shut
>down. Of interest there was quite a bit of noise
>coming from the antenna motors, probably resulting
>from unsynchronized motor activity? Anyway, a switch
>was then made to the new power supply with the 10 foot
>cable. Worked fine. Seemed like the non-switching
>pwr supply "cleaned out the cobwebs" (sorry for the
>non-technical description). No failures. I was able
>to enter calibrate without any difficulty. With the
>new supply, all seemed ok. Switch to the 500 foot
>cable (new one from SteppIR)...worked fine, perfect.
>Ok, now the test, back to the 33 volt switching
>supply...standard SteppIR issue....worked fine...no
>problem. Also of interest, the motors made no unusual
>sounds...smooth. Next test, back to the original 500
>foot cable that would not work previously, except with
>one motor disconnected(only 3 of 4 motors connected).
>Worked fine...perfect, first with the HD supply then
>again with the standard issue power supply...no
>problems at all.
>
>Now to test the antenna...after going through the
>troubleshooting guide and with some phone support from
>Jerry, it appears that there is a problem with the
>motor on the reflector. So, once that is changed out,
>it should work fine...fingers crossed.
>
>So what happened? Beats me. The SteppIR guys are
>correct, it does work with cables greater than 400
>feet. Maybe with this cable length there is an
>increased sensitivity to increased motor load, causing
>the power supply to shut down?All of you engineers out
>there will most likely be able to provide a more
>accurate analysis. Perhaps the dissection of the
>motor will show what happened. All motors were
>working when the antenna went up, so not sure what the
>problem was.
>
>Hope this experience provided some usefull information
>for all of you steppir users out there!
>
>73, Bill
>
>
>
>
>
> ____________________________________________________________________________________
>Luggage? GPS? Comic books?
>Check out fitting gifts for grads at Yahoo! Search
>http://search.yahoo.com/search?fr=oni_on_mail&p=graduation+gifts&cs=bz
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|