I have a 5 section Heights I pulled out of the town dump about 20 years ago
thinking I might make a 80M vertical out of it.. Every section was split
from ice. So much for a stupid design!
Now that aluminum scrap is up I'll take it to the scrap yard.
Carl
KM1H
----- Original Message -----
From: "Gary Schafer" <garyschafer@comcast.net>
To: "'Roger (K8RI)'" <K8RI-on-TowerTalk@tm.net>; "'K4SAV'"
<RadioIR@charter.net>; <towertalk@contesting.com>
Sent: Monday, July 02, 2007 12:04 AM
Subject: Re: [TowerTalk] Tower design question
>I know of two manufacturers that do it "upside down". Heights is one and
> there is another (can't recall the name) that looks almost like it that
> is
> also upside down. They are aluminum towers and each section is tapered (so
> you can't install them the wrong way) and the upper section joins the
> lower
> section by fitting inside of the lower part. It makes a nice funnel for
> rain. I have one.
>
> 73
> Gary K4FMX
>
>> -----Original Message-----
>> From: towertalk-bounces@contesting.com [mailto:towertalk-
>> bounces@contesting.com] On Behalf Of Roger (K8RI)
>> Sent: Friday, June 29, 2007 6:52 PM
>> To: K4SAV; towertalk@contesting.com
>> Subject: Re: [TowerTalk] Tower design question
>>
>>
>>
>>
>> >I thought this was an interesting question, but no one tackled it except
>> > for one guy who said that's the way it's done. So is that really the
>> > reason?
>>
>> I saw one answer that said that is *not* the way it is done.
>> I have never seen a tower designed the way you describe. They are all the
>> other way around. The larger tube or bell on on the upper section and
>> sets
>> down *over* the lower. Small end should always point up with the next
>> section setting down *over* it.
>>
>> That will still not keep water out of the legs except for rain.
>> Atmospheric
>> pressure changes be they barometric changes or due to temperature changes
>> will cause water to condense inside the tower legs which is the reason
>> for
>> the bottom section setting in pea gravel or sand below the frost level so
>> it
>> can drain.
>>
>> Roger (K8RI)
>>
>> >
>> > Floyd Rodgers wrote:
>> >
>> >>Something has been bothering me for a while. With all the discussion
>> >>and
>> >>problems with tower leg corrosion, filling with water and splitting,
>> etc.
>> >>Why do almost ALL the manufacturers design the joints to telescope
>> inside
>> >>from above which leaves water able to run inside joints and fill tubes?
>> >>Why not simply invert the connection by telescoping over the bottom
>> >>section so water just runs outside not through the joint. I know there
>> is
>> >>no difference in joint strength or assembly difficulty, so why?
>> >>_______________________________________________
>> >>
>> >>
>> >>
>> >>_______________________________________________
>> >>TowerTalk mailing list
>> >>TowerTalk@contesting.com
>> >>http://lists.contesting.com/mailman/listinfo/towertalk
>> >>
>> >>
>> >>
>> >
>> > _______________________________________________
>> >
>> >
>> >
>> > _______________________________________________
>> > TowerTalk mailing list
>> > TowerTalk@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/towertalk
>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|