Towertalk
[Top] [All Lists]

Re: [TowerTalk] Neverseize on rohn tower legs

To: <w3yy@cox.net>, <towertalk@contesting.com>
Subject: Re: [TowerTalk] Neverseize on rohn tower legs
From: Tek Supp <teksaport@hotmail.com>
Date: Tue, 5 Jan 2010 20:46:26 -0700
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
I disagree Bob.  I was given a Rohn 25 40' and had to dismatel it.  The top 
section was so stuck that I had to use a couple of 2x4 pieces across the steps 
and my car sissor jack to seperate it.  It did not matter that I had a ground 
crew and it didn't matter that constant presure was applied on the rope from 
the ground crew.  It was STUCK!

 

Thanks,

John

K7ALA 

 

 


 
> From: w3yy@cox.net
> To: towertalk@contesting.com
> Date: Tue, 5 Jan 2010 19:55:09 +0000
> Subject: Re: [TowerTalk] Neverseize on rohn tower legs
> 
> Tony -
> 
> As previously noted, neverseize or not, you just need a ground crew to put a
> little upward pressure on the section while someone is on the tower
> assisting with the separation. No big deal. A tower jack or similar device
> will help in difficult situations. 
> 
> Now, if you want to do this without ground support, its more difficult.
> Take off the bolts and go to the ground and put constant pressure on the
> section yourself and tie it off, then go back up and wiggle it to free it.
> Or, maybe hang some heavy weights (two bags of concrete) on the rope going
> to the gin pole and go up and try to free the section.
> 
> Good luck. I've assembled and disassembled tower sections single-handed,
> but it's much easier if you can get some ground support. 
> 
> 73, Bob - W3YY
> 
> 
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of anthony
> Sent: Monday, January 04, 2010 9:50 PM
> To: TowerTalk@contesting.com
> Subject: [TowerTalk] Neverseize on rohn tower legs
> 
> I errected my rohn 25g in 1999 using neverseize on each leg for easy
> disassembly, Now that I might move Im not sure how to remove each section. I
> do have a very well made gin pole but how in the heck will I pull the
> sections apart??? I was thinking a 2x6 board and a small hydraulic car jack.
> Any other Idea's would greatly be appreciated. thanks guys.
> 
> tony k2vi
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
> 
> _______________________________________________
> 
> 
> 
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
                                          
_________________________________________________________________
Hotmail: Trusted email with powerful SPAM protection.
http://clk.atdmt.com/GBL/go/177141665/direct/01/
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>