Towertalk
[Top] [All Lists]

Re: [TowerTalk] TowerTalk Digest, Vol 133, Issue 3

To: towertalk@contesting.com
Subject: Re: [TowerTalk] TowerTalk Digest, Vol 133, Issue 3
From: jeffhook@comcast.net
Date: Thu, 2 Jan 2014 23:41:26 +0000 (UTC)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>

I put in a foundation for a used HDX555 in Oct of 2013. (5'x5'x7.5') at a cost 
of approx. $18 00 . It adds up fast! (have lots of pics of it all) 



I did all the work myself and it took 2 weeks to complete.  I hand dug the hole 
to 4' &  shored up the first 4' plus 8 " form sticking out the top. 

I then finished digging another 3' down with no shoring. I built rebar cage in 
the hole, added "T " bracket with new ancho r bolts and poured the concrete . 

At age 50, It nearly killed me to hand dig it.  I ordered 8 yards of concrete 
as I didn't want to fall short over a few $$ savings and the pour was at 4:30 
PM so no more trucks that night . 

I placed base so truck could access hole but I have some big 100 foot long  
ruts to repair this spring.   

If I had to do it over again, I would have ordered harder & longer anchor bolts 
from Portland bolt . The short low grade bolts from US tower seem like a weak 
link to me and their overpriced . 



Free  -   Dig hole 

$10 0  -   wood forms/shoring/misc. 

$20 0  -   rebar cage 

$265    -  Three new a nchor bolts from US tower (225+shipping : -( 

$110 0 - 8 yards of 3500lb concrete 

$40  -    Rental of snake vibrator (don't forget this!) 

$4 5  -    Ground rods & wire  at bottom of hole (still need to add more 
grounding this spring) 

$40  -    Beer to get me thru it all !! 



Jeff - KDØORH 

  



Message: 1 
Date: Thu, 2 Jan 2014 11:05:49 -0600 
From: "Marsh Stewart" <marsh@ka5m.net>k 
To: <towertalk@contesting.com> 
Subject: [TowerTalk] Tower Foundation (was Concrete Prices) 
Message-ID: <346BBB5A901D4A59AC66FB92F1954F0B@i7MarshSept13> 
Content-Type: text/plain;        charset="us-ascii" 

I live in NW Louisiana. I'm looking for a concrete contractor to install a 
base per specs for a US Tower HDX-555. I need a hole 5' X 5' 7.25', rebar, 
about 7 cubic yards of concrete, and 3 anchor bolts in the right place. I 
have the anchor bolts and base. (If the layout of my lot, house, and pool 
would allow it, I'd put up 60' of Rohn 45G, with 2 sets of guy wires.) 

A major consideration is that access to my backyard is 42.5" wide through a 
walk gate and between an A/C compressor and a brick wall. If the A/C 
compressor were temporally removed the width of access would increase 4" to 
46.5" - not wide enough I'm told for even the smallest of back hoes. 
Removing a section of fence for better access is not an option. 

Almost surely the hole will have to be dug by hand and the excavated dirt 
moved by wheelbarrow to the front yard to be scoped up by a front-end 
loader. 

Bid #1: $6,880 - contractor never showed up. The one time I did run him down 
to check with him he wanted to change the specs to a 6' X 6' X 6' hole. 
Right or wrong, I'm going to go by US Tower's specs. 

Bid #2: $9,000     

Do those prices sound reasonable? They sounds high to me, but I have no 
reference as to what concrete work should cost. 

73, 
Marsh, KA5M 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>
  • Re: [TowerTalk] TowerTalk Digest, Vol 133, Issue 3, jeffhook <=