On 2/6/2014 11:14 AM, Patrick Greenlee wrote:
Is it a bushing or a bearing?
I would advise against removing a pressed on bearing, or bushing by
tapping on small spots as there is no guarantee the bearing or bushing
will cone out straight and if it doesn't it can distort the hole into
which it was pressed, sometimes drastically. The narrower the bearing
the more likely it will tip. If the pulley is of a soft material such as
aluminum (which it probably is), it can easily be damaged and make the
hole "out of round". This seems simple, but it takes skill and if
expensive and difficult to replace, not a good place to learn. Pat's
suggestion for using a socket to press the bearing in is also a good way
to press one out. Instead of larger you just need a socket who's OD is
slightly smaller than the bearings OD (I prefer a deep well socket). For
some, it's easy and hard for others. Not all of us are mechanically
inclined. I was raised on a farm where we did our own repair work and
improvisation was the word of the day. We rebuilt an old threshing
machine into a combine.
A much simpler approach is to take an Aluminum dowel, 3 or 4" long and
slightly smaller than the OD of the bearing/bushing. Make sure the face
is flat and perpendicular to the long axis of the dowel. Carefully keep
the face flat against the bearing/bushing and tap on the back end of the
dowel. If the bearing has a raised center, just drill out ted center of
the dowel enough to clear the raised part. You could "probably" get a
machinist to face off the ends of a 3 or 4" dowel for a couple of bucks.
Know a friend who owns a lathe? Facing a dowel isn't precision work.
This should easily remove a pressed in bearing or bushing. The hole and
bearing are an interference fit. If it's a bushing, as a last resort a
new one can be made of oilite. Remember it's an interference fit, even
oversize by a Little will cause the ID to change when pressed in. Then
you have to ream the ID with an adjustable reamer. Check prices of
adjustable reamers on Grizzly.com! If you don't have the equipment or
skill, find a good machinist.
There are many ways to make a simple press, but although simple it'd
take more than the many words I've already used.
73 and good luck
Roger (K8RI)
It is likely but not a certainty that the bearing is pressed on and
will need to be pressed off or pulled with a bearing/pulley puller.
If you elect to try to pry it off do go around and around making just
a little progress on each "bite" and be patient if it takes many
revolutions. Most likely there will be a number on the bearing that
you can use to secure a replacement. If no number then take the
bearing with you to Graingers or other similar vendor or an auto parts
store. You need to match the size exactly to make it fit properly.
If you have a number then Google it to find sources. Mind the load
ratings and do not use a bearing not up to the task. Leave a good
safety margin even if it costs a few bucks more.
If you install the bearing yourself be careful to not cock it when
inserting it. You can select a socket from your socket wrench set to
use as a tool to press (tap with a hammer or squeeze in a vise) the
bearing into place. The socket you select should fit such that all
the force you apply to the socket presses on the part of the bearing
in contact with the pulley and does not touch the part where the balls
are.
If you use a hammer or a vise (or hydraulic press if available) you
should press a little then rotate the pulley part of a turn and press
again. This will help prevent cocking the bearing. The farther in the
bearing is pressed the less important the rotating becomes. Rotating
is the most important when getting the bearing started. Look at it
closely when getting the bearing started and make corrections early on
before pressing the bearing even 1/4 of the way home.
Hey, it is easier than my comments may make it seem. I have done it
successfully and I am strictly self taught in mechanic stuff.
If you have additional questions or concerns that you would want to
send direct, I am good in QRZ.
73,
Patrick NJ5G
-----Original Message----- From: Mike Reublin NF4L
Sent: Thursday, February 06, 2014 9:37 AM
To: towertalk reflector
Subject: [TowerTalk] HG70HD pulley
While working on getting the new puppy ready for duty, I discovered
the pulley at the top of the main section would not turn. I soaked it
with PB Blaster and got it to go maybe 1/8 turn.
I took it out, cleaned it well, put a little grease in the hole and
put it back in. There is quite a bit of slop now on the axle.
Did I lose part of a bearing? Any suggestions for a fix or replacement?
73, Mike NF4L
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________
No infections found in this incoming message
Scanned by iolo System Shield
http://www.iolo.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
---
This email is free from viruses and malware because avast! Antivirus protection
is active.
http://www.avast.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|