Towertalk
[Top] [All Lists]

Re: [TowerTalk] Phillistran

To: "towertalk@contesting.com" <towertalk@contesting.com>
Subject: Re: [TowerTalk] Phillistran
From: Ken Beals <k6mr@outlook.com>
Date: Sun, 25 May 2014 23:13:00 +0000
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
The tower did have a strange color to it. And I don’t think any of the sections 
were still straight once it went over. I didn’t take any chances and just had 
the demo guy scrape it all up into a pile and send it to the scrap yard. 


Ken K6MR






From: Jim W7RY
Sent: ‎Sunday‎, ‎25‎ ‎May‎, ‎2014 ‎16‎:‎10
To: Ken Beals, towertalk@contesting.com





Sorry for your loss... But....

I would have wanted a new tower and beam anyway. The galvanizing on the 
tower was probably gone.


73
Jim W7RY



-----Original Message----- 
From: Ken Beals
Sent: Sunday, May 25, 2014 3:48 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Phillistran

The aforementioned fire victim was me. The 20 foot steel ends on the guys 
were of little help when the flames were 100 feet high. The tower was 80 
feet, and everything on the tower that wasn’t steel was vaporized. The 
ground temperature around the tower was high enough to melt most of the 
spare aluminum stacked in the area.


A 50 foot tower next to the house was saved, but the plastic shroud on the 
cell repeater antenna at the top was melted.


Let’s just say this necessitated a complete station rebuild.


Ken K6MR






From: Wayne Kline
Sent: ‎Sunday‎, ‎25‎ ‎May‎, ‎2014 ‎14‎:‎05
To: Chuck Smallhouse
Cc: towertalk@contesting.com





I am under the impression ,that Phillistran installation guid recommends 
appropriate steel/EHS
Guy wire at a safe tamper proof and ground fire height.
I have installed a number of both Phillistran and PollyRod towers,  guy / 
ground safety hight
Plugged into the total guy equation .

Wayne. W3EA

Sent from my iPad

On May 24, 2014, at 11:56 PM, "Chuck Smallhouse" <w7cs@theriver.com> wrote:

> A story for those of you using Phillistran cable for guying a tower.
>
> I was talking to a ham that lives in far N. CA, in area that is subject to 
> wildfires.  A couple of years ago the area had a bad wildfire that moved 
> in the direction of his QTH, in a somewhat rural area.  Even though the 
> area around his home was quite well cleared, they couldn't save his 
> workshop where most of his test equipment and ham equipment was located.
>
> When he returned after a mandatory evacuation and surveyed the damage , he 
> found that not only was his ham shack destroyed, but also his guyed tower 
> had fallen over.   It turned out that he had guyed it using Phillistrand 
> and that the fire had burned the guys through and which resulted in the 
> catastrophic demise of his tower and beams.
>
> I guess that the lesson to be learned is, to at least have the bottom 
> sections of your  guys be of steel cable and not any type of flammable 
> material, especially if you live in a wildfire prone area.
>
> Chuck,  W7CS, with no Phillistrand guys .
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>