On 8/10/2014 2:24 PM, Larry K4AB wrote:
I'm in the process of assembling the new Force 12 Delta-II-6BA.
I agree with Chip K7JA, that the hand rivet tool is very difficult for
What size rivets are you using? I have a simple "one hand" mechanical
tool. "I think" I purchased it at Lowe's, but that was years
ago.---Nope! It's a Sears Craftsman and has collets to take up to a
1/8th inch shank, or stem. You insert the stem into the tool and add
just enough pressure to hold the rivet with the head against the tool.
Insert the rivet into the hole and squeeze. When closed, it snaps the
stem off, flush with the head. Simple and easy to use. I've used it
on many hundreds if not thousands of rivets from 1/8th inch to 3/16ths
regular pop rivets both Aluminum and SS, Chery (Aircraft blind rivets),
and regular blind rivets. I put an entire Force 12 C19 XR together
without my hand getting tired at age 67. At 74, I can still use it with
little effort and I'm certainly no advertisement for muscles. <:-))
Its been loaned out many times so it's apparently rugged.
I've seen a number of Sonex aircraft built using a similar tool. Prior
to that, I'd never seen pop rivets used in skin and structural members
of aircraft. That takes a lot of rivets! IIRC the Van's series uses
all conventional rivets. Holding a bucking bar properly in place while
some one else uses "the tool" is real exercise. One slip and you are
replacing an expensive sheet of Aluminum and IIRC the wings are
assembled with all flush rivets.
For conventional rivets I can understand the need for a pneumatic tool,
but for pop rivets the correct hand tool takes little effort. No, you
can't do it with two fingers, but you should be able to do it with
little effort.
73
Roger (K8RI)
popping the rivets. Bear in mind that I am no large, athletic guy,
but I'm no little old lady either. The hand riviter is tough to use.
I prefer a simple pneumatic riviter that can be bought for around
$50. The advantage of the pneumatic tool is that you can use
one of your hands to steady the element, and the opposite hand
to "pop" the rivet. The dual-hand riviter that Chip recommends
requires use of both of your hands, making it quite cumbersome.
Of course the pneumatic tool uses an air compressor, which a lot
of folks may already have. If not, a simple "pancake" compressor
which can deliver 90-100 PSI is sufficent and inexpensive.
The pneumatic rivet tool is the only way to fly!
As an aside, the new 6BA looks like an fine piece of workmanship.
The new open-air 40 meter loading coils are LARGE, and seem, at
first glance, to appear vastly superior to the previous versions.
Congratulations to AA7XT, G0KSC, K7JA, XE2K and the team,
and of course N6BT.
Once it gets up and installed, I'll give you an overall assessment and
post some pictures online.
73,
Larry K4AB
On 8/8/14, Chip Margelli <chip@force12inc.com> wrote:
Hello to all.
We've come across a very nice tool for inserting rivets beyond the "small"
1/8" rivets used on smaller elements.
Harbor Freight has an item called the Pittsburgh 18" Heavy Duty Hand
Riveter that sells for all of $19.95. It makes work with 3/16" rivets
effortless, and even a 1/4" rivet does not require major exertion. Trying
to do either of these sizes with a hand pop rivet gun will lead to serious
frustration. The Harbor Freight SKU is 66422, and most HF stores have these
in stock, it seems.
http://www.harborfreight.com/heavy-duty-17-1-2-half-inch-hand-riveter-with-collection-bottle-
66422.html
This tool is especially useful when pulling rivets on larger elements, or
on element-to-boom clamping plates, for beams from various manufacturers,
not just Force 12. And it is much cheaper and less bulky than a pneumatic
rivet gun.
It even comes with a Collection Bottle, important for installers above the
age of 55.
73,
Chip K7JA
Force 12InnovAntennas America
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
--
73
Roger (K8RI)
---
This email is free from viruses and malware because avast! Antivirus protection
is active.
http://www.avast.com
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|