Towertalk
[Top] [All Lists]

Re: [TowerTalk] Shorty Forty Hose Clamp thread

To: Stan Stockton <wa5rtg@gmail.com>
Subject: Re: [TowerTalk] Shorty Forty Hose Clamp thread
From: Michael Murphy <mike@ki8r.com>
Date: Fri, 14 Aug 2015 11:30:15 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
I'm getting ready to put up a TH-11.  Do you have any pictures of what you
are describing? My TH-11 is all hose clamps and I don't want to take this
thing back down after a couple of years to replace an element that feel
apart.

Thanks

On Thu, Aug 13, 2015 at 7:17 PM, Stan Stockton <wa5rtg@gmail.com> wrote:

> See below.
>
> Stan
>
> Sent from Stan's IPhone
>
>
>
> > On Aug 13, 2015, at 10:21 AM, Michael Tope <W4EF@ca.rr.com> wrote:
> >
> > Stan,
> >
> > A couple of questions:
> >
> > 1) Does the counterbore go all the way through the one wall of the outer
> diameter piece?
>
> Yes
> >
> > 2) Is the clearance between the counterbore diameter and the cap screw
> head diameter critical?
>
> Not very critical but you don't want a huge hole for the head of a #8
> socket head cap screw.  Just enough so it passes by the OD on the side
> where you insert it.  The drill bits do a perfect job.
> >
> > Thanks,
> >
> > Mike W4EF................
> >
> >> On 8/13/2015 6:53 AM, Stan Stockton wrote:
> >> After about 40 years of making my own antennas I learned something a
> few years ago when faced with assembling 65 tribanders (520 elements) we
> made for WRTC2014.
> >>
> >> I was introduced to the element joint attachment method I am told is
> used by Optibeam.  I was skeptical when I heard the verbal description,
> having settled on pop rivets after every other conceivable method about 20
> years ago.
> >>
> >> I made one element with pop rivets and another with a single stainless
> steel socket head cap screw with a counterbore (head clearance on socket
> head screw) for one wall of the larger diameter tubing for each joint, then
> grabbed each one in the center and violently shook them back and forth.
> The one with SHCS joints felt like one solid piece of tubing as compared to
> the pop riveted one.
> >>
> >> It is so easy and so solid, I will never mess with pop rivets again.
> >>
> >> A V block fixture with stops, drill press and some of these bits along
> with straight bits for the smaller diameter tube drilling are all that is
> needed.
> >>
> >>  http://www.wttool.com/index/page/category/category_id/14686/
> >>
> >> make the job easy in comparison to many methods.  The counterbore is
> important.  Use stainless nylock nuts.
> >>
> >> YMMV but I'm sold on it.
> >>
> >> 73...Stan, K5GO
> >>
> >> Sent from Stan's IPhone
> >
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>



-- 
-----------------------------------------------
*Michael Murphy - KI8R*

mike@ki8r.com

www.ki8r.com

*614-371-8265 (cell)*

-----------------------------------------------
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>