DX Engineering, where I bought the Comteck 8 position switches asked me to
send photos and did provide me with the information I needed. They said I
bought the switches in 2008, had no idea it was that long ago. If I am
satisfied with ham equipment I often buy a backup, which in this instance I
never used.
Thanks for the help!
Dave, AL7HG
On Thursday, January 26, 2023 at 05:26:57 PM EST,
towertalk-request@contesting.com <towertalk-request@contesting.com> wrote:
Send TowerTalk mailing list submissions to
towertalk@contesting.com
To subscribe or unsubscribe via the World Wide Web, visit
http://lists.contesting.com/mailman/listinfo/towertalk
or, via email, send a message with subject or body 'help' to
towertalk-request@contesting.com
You can reach the person managing the list at
towertalk-owner@contesting.com
When replying, please edit your Subject line so it is more specific
than "Re: Contents of TowerTalk digest..."
Today's Topics:
1. Re: RG-6 Coax For Receive Loop? (Grant Saviers)
2. Need Comtek manual (Dave Kaiser)
3. Re: Need Comtek manual (Jim W7RY)
4. Re: Need Comtek manual (Tim Duffy)
5. Assembling a Yagi (Art Greenberg)
6. Common Mode Choke Locations (Art Greenberg)
7. Re: Common Mode Choke Locations (Jim Brown)
8. Re: Assembling a Yagi (Doug Christensen)
9. Re: Assembling a Yagi (Art Greenberg)
10. Re: Assembling a Yagi (Art Greenberg)
----------------------------------------------------------------------
Message: 1
Date: Thu, 26 Jan 2023 09:10:58 -0800
From: Grant Saviers <grants2@pacbell.net>
To: "towertalk@contesting.com" <towertalk@contesting.com>
Subject: Re: [TowerTalk] RG-6 Coax For Receive Loop?
Message-ID: <77af8f38-f8bb-68ea-7a95-46fd7616446d@pacbell.net>
Content-Type: text/plain; charset=UTF-8; format=flowed
Some comments-
RG6 is a good choice, I use it for bidirectional Beverages and for feeds
to all Rx antennas.
For 80 and below VLF avoid the steel core RG6 since the Cu flash is
designed for VHF/GHz skin depths. So the solid Cu center wire is
available and read the fine print on ebay.
The Thomas & Betts and other premium cable crimp connectors are a must
with the appropriate prep and crimp tools.
For chassis F female connectors the Amphenol ones with 4 screws are
highly advised. The mount won't loosen and the pin grip is solid. Not
cheap but chasing noise or faults in phased Rx antennas has not been
fun. Any knockoffs of these I've found are not well made.
Flooded cable is pretty messy to work with, I prefer burying in a conduit.
IIRC, W8JI made some measurements on shield effectiveness. Quad shield
is the standard and again known brands might be advisable.
The usual binocular core transformers which are easy and cheap to make
are one way to kill CM. RG316 micro TFE coax wound on smaller #31
ferrite toroids can yield a compact cheap CM choke also. Crimp BNC
connectors are available. I use the large #31 clamp ons on the RG6 at
each Rx antenna feedpoint if I haven't built in a transformer and/or
RG213 choke.
Also, I am not a fan of using the RG6 as the means to deliver DC power
if needed to the Rx elements, especially for home QTH antennas. Any
even very high R leakage paths for -xxDbm signals will cause noise,
likely intermittent, (ask me a how I know) which is super hard to find.
Grant KZ1W
On 1/25/2023 20:10, Tony wrote:
> All:
>
> I need coax for an amplified receive loop and I'm considering RG-6 as a
> cheap alternative to the more expensive coax. I'm concerned with
> common-mode noise and was wondering if quad-shield RG-6 would be better
> than standard? Also wondering what type of choke to use i.e., material
> turns etc. The loop is designed for VLF to HF but primary use will be
> for 160 and 80.
>
> Thanks, Tony
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
Message: 2
Date: Thu, 26 Jan 2023 17:26:39 +0000 (UTC)
From: Dave Kaiser <kaiserdr@yahoo.com>
To: "towertalk@contesting.com" <towertalk@contesting.com>
Subject: [TowerTalk] Need Comtek manual
Message-ID: <1398371283.1442019.1674753999624@mail.yahoo.com>
Content-Type: text/plain; charset=UTF-8
I am looking for a manual for the Comtek RSV 8 antenna connector switch. Have
attempted to contact Comtek and DX Engineering, where I bought the original, no
luck. I need to know the wiring from the control box to the switch.
Dave Kaiser, AL7HG
------------------------------
Message: 3
Date: Thu, 26 Jan 2023 11:27:38 -0600
From: Jim W7RY <jimw7ry@gmail.com>
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Need Comtek manual
Message-ID: <04d2d78a-2578-bcff-9029-102fd072e997@gmail.com>
Content-Type: text/plain; charset=UTF-8; format=flowed
Call DX engineering on the phone.
Jim W7RY
On 1/26/2023 11:26 AM, Dave Kaiser via TowerTalk wrote:
> I am looking for a manual for the Comtek RSV 8 antenna connector switch.
>Have attempted to contact Comtek and DX Engineering, where I bought the
>original, no luck. I need to know the wiring from the control box to the
>switch.
> Dave Kaiser, AL7HG
>
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
--
Thanks and 73, Jim W7RY
------------------------------
Message: 4
Date: Thu, 26 Jan 2023 12:57:16 -0500
From: "Tim Duffy" <k3lr@k3lr.com>
To: "'Dave Kaiser'" <kaiserdr@yahoo.com>, "reflector -tower"
<towertalk@contesting.com>
Subject: Re: [TowerTalk] Need Comtek manual
Message-ID: <02a201d931af$a125ff00$e371fd00$@k3lr.com>
Content-Type: text/plain; charset="us-ascii"
Hello Dave
We will help you
K8RR will take care of you
Stand by for a response
73
Tim K3LR
CEO DX Engineering
-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of Dave
Kaiser via TowerTalk
Sent: Thursday, January 26, 2023 12:27 PM
To: towertalk@contesting.com
Subject: [TowerTalk] Need Comtek manual
I am looking for a manual for the Comtek RSV 8 antenna connector switch.
Have attempted to contact Comtek and DX Engineering, where I bought the
original, no luck. I need to know the wiring from the control box to the
switch.
Dave Kaiser, AL7HG
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
Message: 5
Date: Thu, 26 Jan 2023 13:33:46 -0500
From: Art Greenberg <art@artg.tv>
To: towertalk@contesting.com
Subject: [TowerTalk] Assembling a Yagi
Message-ID: <332ad798-8e07-3fc2-8164-c7b72bc99638@artg.tv>
Content-Type: text/plain; charset=UTF-8; format=flowed
The instructions for setting element length aren't clear. Do I measure
from element tip to the side of the boom, or to the center of the boom?
I think its the later ...
TNX
--
Art Greenberg
WA2LLN
art@artg.tv
------------------------------
Message: 6
Date: Thu, 26 Jan 2023 13:52:39 -0500
From: Art Greenberg <art@artg.tv>
To: towertalk@contesting.com
Subject: [TowerTalk] Common Mode Choke Locations
Message-ID: <081ca86a-be2d-d304-a762-74b2ff4fefed@artg.tv>
Content-Type: text/plain; charset=UTF-8; format=flowed
I seek a better understanding of the proper application of common mode
chokes.
First, the setup:
I have several coax-fed antennas on a crank-up tower. The coax shields
are bonded to the tower at the top of the tower (at the end of the rotor
loop) and near the bottom of the tower. The bottom of the tower is in
turn bonded to a fairly extensive lightning ground system. The coax
leaves the lower bonding point and is bundled with rotor and control
cables, all of which go under ground in conduit to an entrance panel
where the coax encounters lightning arrestors mounted on a copper plate.
There are also lightning arrestors for the rotor and control cables
mounted on the copper plate. There is also a copper strap that runs
alongside the conduit to bond the tower to the copper plate. The copper
plate is bonded to additional ground below it which is also connected to
the mains ground.
The questions:
I realize that the bonding and lightning ground system isn't an RF
ground, but I wonder if it influences the location(s) of common mode chokes?
I -think- a CM choke is appropriate at the antenna feedpoint, despite
the bonding setup. Is that true?
Is an additional CM choke appropriate near the bottom of the tower? On
which side of the bonding at the bottom of the tower?
Is an additional CM choke appropriate before the lightning arrestor? Or
between the lightning arrestor and the equipment?
TNX
--
Art Greenberg
WA2LLN
art@artg.tv
------------------------------
Message: 7
Date: Thu, 26 Jan 2023 12:57:44 -0800
From: Jim Brown <jim@audiosystemsgroup.com>
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Common Mode Choke Locations
Message-ID:
<871b9770-2fc8-1c0a-7ba0-ab703acfae0a@audiosystemsgroup.com>
Content-Type: text/plain; charset=UTF-8; format=flowed
On 1/26/2023 10:52 AM, Art Greenberg wrote:
> I seek a better understanding of the proper application of common mode
> chokes.
k9yc.com/publish.htm
Study the "Cookbook" and the Ham's Guide.
73, Jim K9YC
------------------------------
Message: 8
Date: Thu, 26 Jan 2023 16:22:41 -0600
From: Doug Christensen <auriga1usa@gmail.com>
To: Art Greenberg <art@artg.tv>
Cc: towertalk@contesting.com
Subject: Re: [TowerTalk] Assembling a Yagi
Message-ID:
<CAD4cJu9J6xAPV4yczj_mZL355SgkEUcqxpOcQmHZkyr_+RJsPQ@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"
>From center of where the electrical connection starts near the boom, to
where the element terminates at the outside of the array.
doug
wb1e
73
On Thu, Jan 26, 2023, 12:34 PM Art Greenberg <art@artg.tv> wrote:
> The instructions for setting element length aren't clear. Do I measure
> from element tip to the side of the boom, or to the center of the boom?
>
> I think its the later ...
>
> TNX
>
> --
> Art Greenberg
> WA2LLN
> art@artg.tv
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
------------------------------
Message: 9
Date: Thu, 26 Jan 2023 17:24:50 -0500
From: Art Greenberg <art@artg.tv>
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Assembling a Yagi
Message-ID: <860c166e-fdf8-e693-f597-a54d7fbd6bb9@artg.tv>
Content-Type: text/plain; charset=UTF-8; format=flowed
I think I left out an important detail. Elements are all connected to
the boom. Even the DE, fed with a "beta" match.
On 1/26/23 17:22, Doug Christensen wrote:
> From center of where the electrical connection starts near the boom, to
> where the element terminates at the outside of the array.
>
> doug
> wb1e
> 73
>
> On Thu, Jan 26, 2023, 12:34 PM Art Greenberg <art@artg.tv> wrote:
>
>> The instructions for setting element length aren't clear. Do I measure
>> from element tip to the side of the boom, or to the center of the boom?
>>
>> I think its the later ...
>>
>> TNX
>>
>> --
>> Art Greenberg
>> WA2LLN
>> art@artg.tv
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
--
Art Greenberg
art@artg.tv
------------------------------
Message: 10
Date: Thu, 26 Jan 2023 17:26:37 -0500
From: Art Greenberg <art@artg.tv>
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Assembling a Yagi
Message-ID: <5134f1a1-a043-5894-96a7-1323b34536a0@artg.tv>
Content-Type: text/plain; charset=UTF-8; format=flowed
I should proof read before posting. The DE is insulated from the boom.
Fed with a beta match. Its a Hy-Gain antenna.
On 1/26/23 17:24, Art Greenberg wrote:
> I think I left out an important detail. Elements are all connected to
> the boom. Even the DE, fed with a "beta" match.
>
>
> On 1/26/23 17:22, Doug Christensen wrote:
>> ?From? center of where the electrical connection starts near the boom, to
>> where the element terminates at the outside of the array.
>>
>> doug
>> wb1e
>> 73
>>
>> On Thu, Jan 26, 2023, 12:34 PM Art Greenberg <art@artg.tv> wrote:
>>
>>> The instructions for setting element length aren't clear. Do I measure
>>> from element tip to the side of the boom, or to the center of the boom?
>>>
>>> I think its the later ...
>>>
>>> TNX
>>>
>>> --
>>> Art Greenberg
>>> WA2LLN
>>> art@artg.tv
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>
--
Art Greenberg
art@artg.tv
------------------------------
Subject: Digest Footer
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
------------------------------
End of TowerTalk Digest, Vol 241, Issue 24
******************************************
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|