That was what DIGI Keyer template setting put me on. Last night I figured
and PTT on PHONE and RTTY works now. (Always use full break-in on CW
instead PTT.)
Anyway thanks for adivices. I think every thing is working as intended.
----- Original Message -----
From: "Joe Subich, W4TV" <w4tv@subich.com>
To: "'Jon Suehiro'" <nn5t@attglobal.net>
Cc: <writelog@contesting.com>
Sent: Tuesday, October 23, 2007 1:03 AM
Subject: RE: [WriteLog] WriteLog - DIGI Keyer - IC7800
>
> Jon,
>
>> WL DIGI Keyer
>> (CAT level jumpers set to RS-232)
>> CommSlot1=4 CW (No Rig) PTT: RTS
>> CommSlot2=5 Icom IC-7800 9600 Poll Radio 9600 8N2
> x Comm PTT YES
>> CommSlot3=6 No Rig CW: DTR
>> CommSlot4=7 No Rig FSK: x PTT
>> x All mode PTT on CW port RTS
>
> If you are going to use "All mode PTT on CW Port RTS" the ports
> for CW and PTT need to be the same in Router (both COM4 or both
> COM 6).
>
> See: www.microHAM.com/Downloads/DK_WriteLog_Setup.pdf
>
> 73,
>
> ... Joe Subich, W4TV
> microHAM America
> http://www.microHAM-USA.com
> http://groups.yahoo.com/group/microHAM
> support@microham.com
>
>
>> -----Original Message-----
>> From: writelog-bounces@contesting.com
>> [mailto:writelog-bounces@contesting.com] On Behalf Of Jon Suehiro
>> Sent: Sunday, October 21, 2007 9:27 PM
>> To: Joe Subich, W4TV; 'Barry'
>> Cc: writelog@contesting.com
>> Subject: Re: [WriteLog] WriteLog - DIGI Keyer - IC7800
>>
>>
>>
>> Thanks for advises.
>>
>> Joe, I know about DIGI Keyer. I have a separate audio cable
>> from SB to rig
>> mic input with an isolation transformer (and HC4 audio coming
>> in parallel
>> with SB audio). Also " Check the "PTT" box on the FSK port
>> (COM 7) in
>> Router (MMTTY will operate PTT in FSK) and set PTT to COM 6
>> RTS WL Will
>> operate PTT in CW and SSB. " has been already tried at the
>> initial setting.
>>
>> Barry, 8N2 is not what I set to. I set IC7800 Decode Baud
>> Rate to 9600, WL
>> Port Setup Baud Rate to 9600, the rest (8N2) is picked up by
>> microHam USB
>> Device Router at the Radio (COM5 open 9600 8N2 < >).
>>
>> With additional tinkering around, I found a case of following
>> set up work on
>> Phone.
>>
>> WL
>> DIGI Keyer (CAT level jumpers set to RS-232)
>>
>> CommSlot1=4 CW (No Rig) PTT: RTS
>> CommSlot2=5 Icom IC-7800 9600 Poll x Comm PTT YES Radio 9600 8N2
>> CommSlot3=6 No Rig CW: DTR
>> CommSlot4=7 No Rig
>> FSK: x PTT
>> x All mode PTT on CW port RTS
>>
>> ----------
>>
>> I tried to swap PTT RTS and CW DTR in between COM4 and COM6 on Router
>> setting --- did not work. Tried every possible combination
>> of WL Port
>> Setup Comm PTT YES or NO, including "All mode PTT on CW port
>> RTS" and did
>> not make any difference.
>>
>> Only thing it made to work is to change the WL Port Setup CW
>> from COM4 to
>> COM6 (DIGI Keyer set up remains as indicated in sample
>> setup). By doing
>> so, the CW keying won't reach to the rig. I guess I have to
>> remember on
>> each contest if CW should be on COM4 or COM6 on WL by mode.
>>
>> ARRL 10 meter and VHF contest, I guess I need to use a foot
>> switch on the
>> Phone to send the message from Sound Card.
>>
>> If any one with set up condition - suggestion, please let me know.
>>
>> 73, Best DX and Contesting de NN5T Jon
>>
>>
>> -----Original Message-----
>> From: Joe Subich, W4TV [mailto:w4tv@subich.com]
>> Sent: Sunday, October 21, 2007 3:15 PM
>> To: 'Barry'; 'Jon Suehiro'
>> Cc: writelog@contesting.com
>> Subject: RE: [WriteLog] WriteLog - DIGI Keyer - IC7800
>>
>> Barry/Jon,
>>
>> If you have COMM PTT enabled, it is possible that the "PTT Off"
>> command is getting clobbered by collisions on the CI-V bus.
>> Disable COMM PTT and use RTS on the CW port (or LPT if you have
>> one) for SSB PTT.
>>
>> 73,
>>
>> ... Joe, W4TV
>>
>> -----Original Message-----
>> From: writelog-bounces@contesting.com
>> [mailto:writelog-bounces@contesting.com] On Behalf Of Barry
>> Sent: Sunday, October 21, 2007 7:24 AM
>> To: Jon Suehiro
>> Cc: writelog@contesting.com
>> Subject: Re: [WriteLog] WriteLog - DIGI Keyer - IC7800
>>
>> Jon,
>> I"m not familiar with the Digi Keyer, but I have a similar setup and
>> problem.
>> I also replaced a 1000D with a 7800. Everything works fine in CW and
>> RTTY, however the PTT doesn't work in SSB and remains key down when I
>> activate it.
>>
>> I sent an Email to K5DJ, but no response.
>>
>> One thing - I believe the serial params should be 8N1. Only
>> Yaesu uses
>> 2 stop bits.
>> Let me know if you come up with anything.
>> 73,
>> Barry
>>
>> --
>>
>> Barry Kutner, W2UP Newtown, PA
>>
>>
>> Jon Suehiro wrote:
>>
>> This week, I replaced my long time favor FT1000D with IC7800
>> in the main rig
>> position.
>>
>> --- Same PC with XP Pro, WriteLog latest version, DIGI Keyer
>> with latest
>> microHAM USB Device Router 5.0.1, and less than 1 week old IC7800 ---
>>
>> Actually I received DB15-IC7800 cable for microHam to replace
>> the original
>> cable for FT1000, nothing else is changed.
>>
>> WriteLog PORTS are
>>
>> WL
>> DIGI Keyer (CAT level jumpers set to RS-232)
>>
>> CommSlot1=4 No Rig PTT: RTS
>> CommSlot2=5 Icom IC-7800 9600 Poll x Comm PTT YES Radio 9600 8N2
>> CommSlot3=6 CW (No Rig) CW: DTR
>> CommSlot4=7 No Rig
>> FSK: x PTT
>> x All mode PTT on CW port RTS
>>
>> IC7800 CI-V Baud Rate Auto
>> CI-V Address 6Ah
>> CI-V Transceive ON
>> RS-232C Function CI-V
>> Decode Baud Rate 9600
>>
>> Frequency / Mode are talking to the radio from WriteLog.
>>
>> I can test DIGI Keyer PTT OK through Device Router (DIGI
>> Keyer panel LED PTT
>> ON and IC7800 on TX).
>>
>> ISSUE is --- On FSK, the radio PTT is actually keyed from
>> WriteLog with
>> MMTTY but WriteLog DVK (sound board) does not key the IC7800
>> PTT on SSB
>> (DIGI Keyer panel LED PTT stays OFF).
>>
>> At the same condition, FT1000D is keyed when DVK is activated
>> through the
>> function keys. I used old COM port setup with FT847 on
>> COM1, PTT is keyed
>> OK.
>>
>> ----------
>>
>> Smells like some how the issue is within WL but I was unable
>> to find any
>> hint in regard to PTT matter on SSB. Of course the wave
>> file audio output
>> will be transmitted if I keyed the PTT manually from either
>> front panel
>> TRANSMIT or external PTT through ACC jack (or turn on VOX).
>>
>> Any advise why remote PTT is not working ?
>>
>> Thanks de NN5T Jon Suehiro
>>
>>
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web: http://www.writelog.com/
>>
>>
>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|