WriteLog
[Top] [All Lists]

Re: [WriteLog] FSK in MMTTY Plug-in on COM1 != MMTTY v1.66G standalone

To: "[WriteLog]" <WriteLog@contesting.com>
Subject: Re: [WriteLog] FSK in MMTTY Plug-in on COM1 != MMTTY v1.66G standalone
From: "Joe Subich, W4TV" <lists@subich.com>
Date: Fri, 07 May 2010 16:47:06 -0400
List-post: <writelog@contesting.com">mailto:writelog@contesting.com>
 > I have the FSK interface connected to COM1 on the laptop dock (real
 > DB-9).

If the port on the dock appears as COM1 in Windows, set RTTYrite for
COM 1 before you open the MMTTY set-up within the plug-in.  That should
enable FSK on COM1.

73,

    ... Joe, W4TV

On 5/7/2010 3:48 PM, Larry 'Rebar' Rebarchik - N6CCH wrote:
> Joe,
> I have the FSK interface connected to COM1 on the laptop dock (real DB-9).
> As noted before, the setup works fine with MMTTY running standalone, but
> not with WL and the plug-in.
>
> I'll dig around a bit more.
>
>
> rebar
> On Fri, 07 May 2010 15:34:09 -0400, "Joe Subich, W4TV"<lists@subich.com>
> wrote:
>>> I have a laptop docked with Rig Control on COM9 via USB/Serial
>>   >  and FSK on COM1 via<http://www.w3yy.com>   FSK/CW interface box
>>   >  <http://www.w3yy.com/fsk.htm>
>>
>> WriteLog only supports FSK on COM1-COM8.  That limitation also
>> applies to the MMTTY plug-in since the FSK port is set by the
>> WriteLog RTTY Window when the "TU" (MMTTY plug-in) is started.
>>
>> Since you are using the W3YY interface, I assume it is being
>> driven by a USB to serial adapter.  You will need to configure
>> RTTYrite to do "Software generated FSK" on the USB port and
>> make sure that port is in the COM1 - COM8 range.
>>
>> You hardware supplier should be providing this support ...
>>
>> 73,
>>
>>      ... Joe Subich, W4TV
>>          microHAM America, LLC.
>>          http://www.microHAM-USA.com
>>          http://groups.yahoo.com/group/microHAM
>>
>>
>> On 5/7/2010 2:10 PM, Larry 'Rebar' Rebarchik - N6CCH wrote:
>>> I've begun to get some more features sorted out with my K3 and have
>>> discovered that the MMTTY Plug-in for WL does not have the ability to
>>> select SOUND-COM when working in a FSK setup, the last two radio
> buttons
>>> are grey'd out in the setup control panel under WL when running MMTTY
>>> [RTTY
>>> Window].
>>>
>>> Has anyone else discovered this, or am I missing some special
> selections
>>> in my configuration to make this work?
>>>
>>> I have a laptop docked with Rig Control on COM9 via USB/Serial and FSK
> on
>>> COM1 via<http://www.w3yy.com>   FSK/CW interface box
>>> <http://www.w3yy.com/fsk.htm>
>>>
>>> The WL/PC generated CW is working just fine, however, I cannot seem to
>>> get
>>> the RTTY signals to the K3 rig.
>>>
>>> MMTTY v1.66G in standalone mode keys the rig just fine.
>>>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>