WriteLog
[Top] [All Lists]

Re: [WriteLog] v12.35c commport question

To: Writelog@contesting.com
Subject: Re: [WriteLog] v12.35c commport question
From: "Jim Johnson" <jim@kc4hw.com>
Date: Sat, 12 Jan 2019 14:35:42 -0600
List-post: <mailto:writelog@contesting.com>
Well finally see some light at the end of the tunnel!

I cleaned out the WASP nest of comport (both hardware and virtual) thanks to 
the guidance provided on the rttycontesting.com (courtesy of AA5AU - Thanks 
Don).  

BTW Joe, I had NO selected for all comports in Writelog.

But the installation would not make CW from Writelog.  uRouter worked fine.  
Accidentally the radio went into RY mode (it might have had something to do 
with my sudden impact of my fist on the desktop), I did not realize it and 
selected comport 4 for CW and KE1L Winkey and APPLY then OK.   Then I saw that 
the Entry Window Rig button was reading FSK, so I selected CW from the radio 
and then ALT K and type vvv and sure enough CW was generated from the setup.  
So I create a contest sheet for NAQP CW and save it as well as configuration.  
Was able to make a couple of QSOs there.  So I guess the bottom line is that 
the software setup has to go to RY before I can select the comport and type for 
CW, then selected CW and it works--I guess!

I don't understand what I don't understand, but it is working.  Just lucky!

Thanks to all that helped or offered to help.  

73, Jim/KC4HW 

    



----- Original Message -----
From: Jim <jim.kc4hw@gmail.com>
To: <jim@kc4hw.com>
Sent: 1/12/2019 1:42:37 PM
Subject: Fwd: Re: [WriteLog] v12.35c commport question















-------- Forwarded Message -------- Subject: Re: [WriteLog] v12.35c commport 
question
Date: Thu, 3 Jan 2019 15:11:26 -0600
From: Jim Johnson <jim.kc4hw@gmail.com>
To: Writelog@contesting.com


Hey Joe,

Thanks for the help!  Sri for the delay in replying, but my Grandson is 
visiting for a few days.   Don't get many visits from him, so can't give up the 
opportunity to spend some time.  Although I am planning on some kind of effort 
in RTTYRU.

Yes I did download the current example configuration file for the MK and 
writelog.   In fact it helped my aging memory to setup up the RTTY 
configuration which appears to be working fine.

I currently have a PCI-e card with port 2, 3, 4 and 5 installed in this 
computer that is not being used now.  Additionally, uRouter, Virtual Port, Show 
All - reveals that I had previously created virtual port for 6 thru 11 that are 
currently being used.  Additionally, ports 12 thru 30 are present but not being 
used.

I really think this is a computer ports problem, because port 6 had been flakey 
as well.  So I was going to remove the PCI-e card and the other Virtual ports 
and then using the procedure described on RTTYContesting.com to make sure that 
those ports are removed from the system ( guess this will work as I am using 
Win 8.1 compooter).  Then I thought that I would reboot and start over with the 
virtual ports in uRouter and Writelog and see where it goes.

BTW I am using port 7 for CAT control for FT-2000 and port 8 for FSK--both of 
these are working without a problem.  In fact all of this was working including 
CW in Writelog 11.29, uRouter before upgrading to Writelog 12.35c.

I 
don't know!  Thanks, Jim/KC4HW



On 1/2/2019 5:08 PM, Joe Subich, W4TV wrote:


Have you checked the example configuration file for MK and Writelog
(in Router -> Help | Download Documents or on-line in the MK area
at www.microHAM-USA.com/Support.html)?

*DO NOT* attempt to use the same port for the radio and CW (K1EL
Winkey).  Also confirm that "COM PTT" for all Ports is set to NO.

73,

   ... Joe, W4TV


On 2019-01-01 12:12 PM, Jim wrote:

My Setup:  Writelog 12.35c and MicroHAM, Microkeyer

Have Comm10 identified and working for CW K1EL Keyer in uRouter. I was able to 
send CW from uRouter.

In Writelog 12.35c, I selected PORTS and set Comm10 for CW and then identify 
K1EL Winkey as the CW Keying Interface.  When I tap APPLY and then OK I am 
getting a "Can't 
open port for Winkey" error.   This implies that something else is using 
Comm10, but I am not aware of anything that is using Comm10.  So I shutdown to 
power off with the computer thinking that this would release Comm10--no luck!

BTW this configuration with Comm10, uRouter and Writelog v11.29 worked.

Any help here?

Jim/KC4HW




_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>