[Here is the properly formatted version of my post. The first post got nuked
somehow.]
I do it with the following message:
TU %C, NOW %L
This is F8, mapped to SEMICOLON. My normal Run Exchange message is F5, mapped
to APOSTROPHE. Thus, all I do is tap SEMICOLON and APOSTROPHE in rapid
succession, then turn my attention to a second radio or the other VFO for SO2V.
The other stations on frequency print:
TU AA5AU, NOW
W5AJ 599 CA CA
Normally, I'm not doing this but just sending F6, my Run QSL message, which is
sent by ENTER, since I use ESM. Thus, all three keys are adjacent to each
other and they are all I use for 99% of my Run QSOs.
For S&P, my call is mapped to OPEN SQUARE BRACKET and my S&P Exchange is mapped
to CLOSE SQUARE BRACKET. Thus, my S&P messages are all right above my 3 Run
messages.
73,
Ed W0YK
-----Original Message-----
From: WriteLog <writelog-bounces@contesting.com> On Behalf Of Ed W0YK
Sent: 02 January, 2021 03:56
To: Robert Wood, P.E. (retired) <woodr90@gmail.com>; WriteLog@contesting.com
Subject: Re: [WriteLog] TU NOW MESSAGE
I do it with the following message: TU %C, NOW %LThis is F8, mapped to
SEMICOLON. My normal Run Exchange message is F5, mapped to APOSTROPHE. Thus,
all I do is tap SEMICOLON and APOSTROPHE in rapid succession, then turn my
attention to a second radio or the other VFO for SO2V. The other stations on
frequency print: TU AA5AU, NOW W5AJ 599 CA CANormally, I'm not doing
this but just sending F6, my Run QSL message which is sent by ENTER, since I
use ESM. Thus, all three keys are adjacent to each other and they are all I
use for 99% of my Run QSOs. For S&P, my call is mapped to OPEN SQUARE BRACKET
and my S&P Exchange is mapped to CLOSE SQUARE BRACKET. Thus, my S&P messages
are all right above my 3 Run messages. 73,Ed W0YK
-------- Original message --------From: "Robert Wood, P.E. (retired)"
<woodr90@gmail.com> Date: 1/1/21 23:14 (GMT-08:00) To:
WriteLog@contesting.com Subject: [WriteLog] TU NOW MESSAGE This question deals
with TU but not calling CQ instead working next stationin Que I have the "="
key setup in writelog to pop next callsign from QUE should be a means to use
the = key board shortcut in message such that apreprogrammed message could look
likeLET'S ASSUME THAT %= would Do that %R TU %L NOW %= %C 599 TX TX %E did try
%= in a message, it does pop from the QUE but the message sent is amess..also
appears that what callsign is in entry field for RTTY is the one sentfor that
Message using %C (doesn't read in next call) QUESTION:is there method for one
message to send TU or %C TU, the callsign that of the station being logged Then
the message pops from QUE and sends NOWThen sends the new callsign in entry
window and report otherwise it's three keystrokes (seems)TU messageKey to pop
from queTh
en use report message to send report to next callsign 73 W5AJ
RobertMidland, Texashttp://w5aj.eqth.net/Infinity.pdf
_______________________________________________WriteLog mailing
listWriteLog@contesting.comhttp://lists.contesting.com/mailman/listinfo/writelogWriteLog
on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|