Agreed, to bad Digirite got into a P^&*ing contest with the Princeton group
I'm still using the original Digirite with Writelog 12.43E and in fact I am
not upgrading WriteLog because I do not want to try all the voodoo to get
the new Digirite to work with it! I'm keeping 12.43E as long as I can.
Maybe some bright programmer can either automate the new Digirite loading
process or re-write Digirite and burn Princeton altogether. When/if that
happens I will upgrade my Writelog.
Yes sports fans it has now become that serious for the Writelog folks. I'm
not alone on this for sure.
Rick WU7W
-----Original Message-----
From: WriteLog <writelog-bounces@contesting.com> On Behalf Of
k3sk@buckwalter.co
Sent: Thursday, September 8, 2022 4:54 PM
To: 'Jay' <ws7ik7tj@gmail.com>; writelog@contesting.com
Subject: Re: [WriteLog] IC-9700 Connection via USB Times out in about 10
seconds
The later versions of Writelog do not have/use an INI file.
This is disappointing for me. I've used Writelog since back pre-version 8.
I love how it handles multiple rig inputs for VHF contests. There is so
much FT8 activity on VHF now, to contest and not be able to work/log FT8
contacts is nearly as bad as not operating at all. I may have to consider
other contest logging options.
de K3SK
-----Original Message-----
From: WriteLog <writelog-bounces@contesting.com> On Behalf Of Jay
Sent: Thursday, September 8, 2022 6:41 PM
To: writelog@contesting.com
Subject: Re: [WriteLog] IC-9700 Connection via USB Times out in about 10
seconds
When you first go into Writelog on the right hand side you can EXPORT the
INI file.
Two things.
1. The USB Cable must be very short -- this is an Icom problem.
2. In the [RIGS] section
Com3:=19200,n,8,2 Com port that you are using BUT 2 Stop
bits.
On 9/8/2022 3:03 PM, <mailto:k3sk@buckwalter.co> k3sk@buckwalter.co wrote:
> HELP !!! VHF Contest is only 1-1/2 days away and I can't get my IC-9700
to
> stay connected to Writelog. I had version 12.6 and it wouldn't work, so
I
> purchased the latest (v12.66) and it still don't work.
>
> When I configure the port settings in WL it connects, and the radio's
> frequency and mode are displayed at the QSO entry window and follow manual
> radio tuning as it should. But after about 10 seconds, the QSO Entry
window
> changes to "No Rig". I've tried several different baud rates with no
> difference in the issue.
>
> The radio is set to the default address, A2H and I don't see where I can
> check or change that in WL.
>
> de K3SK FM07
>
>
_______________________________________________
WriteLog mailing list
<mailto:WriteLog@contesting.com> WriteLog@contesting.com
<http://lists.contesting.com/mailman/listinfo/writelog>
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: <http://www.writelog.com/> http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
--
This email has been checked for viruses by AVG.
https://www.avg.com
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|